6ES5 921-3WB15
Siemens 6ES5 921-3WB15 – CPU 921, S5-130WB / PLC 130WB
Siemens 6ES5 921-3WB15 is a CPU 921 central processor module for the S5-130WB / PLC 130WB arrangement in the SIMATIC S5 family. This S5 CPU executes the user program, evaluates machine inputs and generates output commands. In SINUMERIK PLC applications, it implements the control logic linking machine conditions with NC commands.
When selecting a spare, check the complete 3WB15 order number, hardware revision, basic program and user EPROM together. The CPU 921 designation covers processors for different S5 systems; the three-digit model name alone does not establish program or hardware compatibility.
130WB memory arrangement and EPROM modules
The Siemens System 8 description of the 6ES5 921-3WB / PC 130WB family shows two EPROM-module receptacles. The first module holds the basic program, while the second holds the user program. Record the contents and positions of the installed memory modules separately.
The same family manual specifies internal RAM for approximately 2.9 K instructions and a suitable EPROM arrangement for up to 16 K user-program instructions. These are 130WB family values expressed in instructions, not directly in KB. Verify the actual program area on a 3WB15 against its fitted modules and system version.
The basic-program version must match the machine-specific user program. A current RAM backup obtained through the programming software may differ from an older EPROM image. Establish which machine each program belongs to before replacing the CPU.
PLC program and SINUMERIK operation
The STEP 5 program handles machine logic and auxiliary functions. Depending on the application, these may include lubrication, hydraulics, clamping and tool changing. Check NC–PLC signal and data exchange against the machine wiring diagrams and existing program.
A waiting condition or alarm displayed on the operator panel may result from a field condition expected by the PLC. Compare digital input, digital output and analog module states with the program. Verify machine functions as well as the CPU’s operating indication.
PG access and fault diagnosis
Siemens’ 130WB service instructions describe program testing and U-STACK reading with a PG 670/675. In a suitable SINUMERIK configuration, the NC maintenance display and commissioning software can also support diagnosis. Select the PG interface, programming cable and communication hardware for the installed connection arrangement.
U-STACK helps identify the STOP cause and interruption point. Save this record with the program backup when distinguishing memory-addressing errors, program-structure faults and peripheral failures. Failure to establish a connection alone does not prove that the program has been erased.
Operating controls and system checks
The 130WB family drawing shows a Run/Stop switch, Reset/Rücksetzen and Restart/Wiederanlauf controls. Assess their effects against the startup mode and current system state. Record the operating condition and memory contents before using reset functions.
Check the rack arrangement, power supply, backup battery and expansion hardware. After CPU replacement, module positions, memory selection and peripheral addresses must match the machine hardware list. Distinguish the external system supply from the CPU board’s internal operating supply.
Nearby order-number comparison
6ES5 921-3WB11, 6ES5 921-3WB13 and 6ES5 921-3WB14 are different order numbers within the WB family. 6ES5 921-3UA12 belongs to a different CPU 921 arrangement. Verify the basic program, memory modules, system version and hardware compatibility before considering replacement.
Editor’s Note
When buying a used Siemens CPU, first check the full 921-3WB15 label. Inspect the EPROM receptacles, retainers, contacts and signs of previous repair. Include the basic-program version when choosing a spare.
While the machine is working, back up the PLC program and data blocks. Record both EPROM labels and their module positions. Keep the basic program and user program clearly identified; a working replacement board still needs the correct program arrangement.
Keep NC machine data and other existing backups alongside the PLC backup. A saved PLC program does not cover every part of the machine control. Establish where each data set is stored before battery or board work.
If the S5 system stops, record the indicators and U-STACK contents first. Include memory addressing, supply condition and field inputs in fault diagnosis. Preserve the information needed to diagnose the problem before considering an overall reset.
Switch off power before replacing the CPU or EPROM modules. Afterwards, test auxiliary machine functions and NC–PLC exchange under controlled conditions as well as checking RUN indication. Record the CPU code, EPROM versions and backup filename for the next technician.
OtomasyonAVM resources
+ 6ES5 921-3WB15 model page · Siemens S5 second-hand models · S5 memory cards · About Siemens S5.
Related topics
+ 6ES5 921-3WB11 · 6ES5 921-3WB13 · 6ES5 921-3WB14 · 6ES5 921-3UA12. These links support version and system comparison; they do not guarantee direct replacement compatibility.
Browse SIMATIC S5
+ SIMATIC S5 CPU models · S5 memory modules · S5 interface modules · S5 racks · Siemens second-hand main page.
Siemens and external references
+ Siemens System 8 Commissioning Instructions, PC section, German. Section 18, printed page 18-2: 921-3WB / 130WB family memory arrangement; 18-4–18-7: program testing and U-STACK diagnosis.
+ Siemens S5-130W Version B Operating Instructions, German. Family architecture and service context; technical values from an older revision must not automatically be assigned to the 3WB15.
+ Siemens 6ES5921-3WB15 archived product sheet. The single-page document dated 28 April 2018 states that the product is no longer available; it contains no detailed specification table.