6ES5 455-6AA12

Siemens 6ES5 455-6AA12 – 8-Channel 110 V AC Digital Output Module

6ES5 455-6AA12 is a Siemens SIMATIC S5 digital output module with 8 isolated outputs, a nominal 110 V AC load supply and a nominal rating of 2 A per channel. This member of the S5 digital output range uses the older Robustbauform / A-type construction. The permitted AC supply range is 88–132 V.

System and mechanical compatibility

Siemens catalog ST 53 lists this exact order number for S5-130A and S5-150A systems. For replacement in a SIMATIC S5 system, check the existing rack, rear connections and complete order number together. The “S5 455” designation alone does not establish compatibility between different constructions.

Load current and temperature derating

The permitted current with an output on is 50 mA–2 A. With control relays and similar loads, check both continuous current and pickup current. Compare the load information used for relay and contact selection with this AC output’s limits.

At 55 °C, total loading is limited to 30% of the sum of all eight rated output currents. This corresponds to 8 × 2 A × 0.30 = 4.8 A total; operating every channel continuously at 2 A at that temperature exceeds the limit. Assess board bus consumption separately from the AC load circuit when calculating power supply requirements.

Switching frequency and lamp loads

The catalog specifies maximum switching frequencies of 20 Hz for resistive loads, 11 Hz for lamps and 2 Hz for inductive loads at rated loading. The lamp-load limit is 50 W. Inductive-circuit turn-off takes place when current reaches zero; apply the requirements for the actual load type.

Fuses, indicators and wiring

Short-circuit protection uses a fuse with a blown-fuse indication. The connection drawing shows a red fault/fuse LED and a green signal-state LED. Check cables and connections, load terminals, AC supply and grounding against the drawing for the installed module.

Off-state leakage current

In the “0” state, the catalog specifies up to 5 mA residual current and an output signal level of up to 30 V. Allow for these values with low-consumption loads. When checking a used output module, supplement unloaded voltmeter readings with switching checks using a suitable test load.

Bus consumption and similar order numbers

The catalog gives an internal 5 V bus current of 160 mA and an approximate weight of 0.3 kg. The 6ES5 456-6AA12 listed in the same table has a 220 V AC nominal load supply. The 6ES5 455-7LA11 is also a separate model; the shared 455 designation does not replace a full order-code and construction check.

Other output cards, including 6ES5 450-6AA12 and 6ES5 451-5AA13, require their own voltage, channel-count and wiring assessment. U-construction models such as 6ES5 451-4UA14 also require a separate mechanical and electrical compatibility review.

Used-module inspection and replacement preparation

Compare the relevant digital inputs with output commands and retain the addresses of combined input/output modules in the existing I/O list. Back up the program and memory unit before replacement, and record the S5 system’s addressing arrangement.

For used Siemens modules, assess the label photograph, front connections, fuses and indicators together with load-test results for all eight channels. State the operating condition, included parts and any missing components for the individual item.

Editor’s note

Start with a good look at the label. This card’s load circuit is rated for 110 V AC. Keep it separate from the neighboring 456 model’s 220 V AC rating; a small order-code difference can matter a great deal in the cabinet.

Check the total before loading all eight channels. The 2 A channel rating comes with a temperature-dependent overall limit. Write down each load and add them up before putting the card back to work.

An off-state voltage reading needs a closer look. This model has leakage current. An unloaded meter or a very small load can give a misleading impression, so confirm operation with a suitable test load.

Find the cause of a blown fuse first. Check the load and wiring, then match the fuse rating to the applicable documentation. Replacing the fuse alone may bring the same fault straight back.

Keep the old arrangement easy to reconstruct. Photograph the wiring, mark the terminals and save the program before removal. Then test all eight channels in order so the result is clear.

OtomasyonAVM resources and PDFs

+ Shared SIMATIC S5 manuals and PDF archive

+ S5 digital output modules and model pages

Related topics

+ 6ES5 456-6AA12 – a different AC voltage class

+ 6ES5 455-7LA11 model page

+ Grounding and field connections

Browse SIMATIC S5

+ Back to S5 digital output modules

+ SIMATIC S5 system pages

+ Siemens S5 PLC main page

+ Used Siemens products and models

Siemens and external references

+ Siemens ST 53, 1985 – 455-6 specifications, 8/7 (German)

+ Siemens ST 53 – 455-6 / 456-6 wiring and indicators, 8/21 (German)

+ Siemens ST 53 – exact order number and 130A/150A listing, 9/6 (German)