6ES5 432-7LA11

Siemens 6ES5 432-7LA11 – 16-Channel 48–60 V AC/DC Digital Input Module

6ES5 432-7LA11 is a Siemens SIMATIC S5 module with 16 inputs for 48–60 V UC, meaning AC/DC signals. This member of the S5 digital input range provides optocoupler isolation in four groups of four channels.

The card transfers binary information from control contacts and suitable field devices to the SIMATIC S5 system in the S5-115U/H family. Check the rack, front connector and address allocation against the existing S5-115U CPU and system arrangement. For AC operation, the catalog specifies 47–63 Hz.

Logic levels and input current

Logic 0 is 0–10 V; logic 1 is 30–72 V. The region between 10 and 30 V should not be used as a defined logic state. These thresholds mean that a standard 24 V signal cannot be assumed to produce a reliable logic 1.

Typical input currents are 8.5 mA at 48 V AC/50 Hz, 9.5 mA at 48 V DC, 9.5 mA at 60 V AC/50 Hz and 10 mA at 60 V DC. The Siemens manual permits two-wire BERO connection; compare the sensor’s leakage current and output voltage with this input circuit.

Isolation groups and phase restriction

Each group of four inputs shares an N/M common terminal. Follow the cabinet drawing when arranging commons so that group isolation is preserved. The Siemens manual for this model states that connecting different phases is not permitted. Keep the specified common connections separate from protective grounding.

Front connector and terminal numbers

The card uses a 24-pole front connector; the screw-terminal option is 6ES5 490-7LB11. When replacing cables and connectors, distinguish pole count from terminal numbering: Siemens terminal numbers on this 24-pole connector extend to 47.

Group 1: inputs 3, 5, 7 and 9; N/M common 11. Group 2: inputs 15, 17, 19 and 21; N/M common 23.

Group 3: inputs 27, 29, 31 and 33; N/M common 35. Group 4: inputs 39, 41, 43 and 45; N/M common 47. Match the fitted connector’s labels to the manufacturer’s drawing before wiring.

Response time and long field cables

0-to-1 response time is 2–13 ms; 1-to-0 response time is 10–25 ms. Include CPU scan time when assessing short pulses. Permitted cable lengths are 600 m unshielded and 1000 m shielded.

Addressing: fixed slots and IM 306

The S5-115U input/output addressing arrangement depends on the rack configuration. Fixed slot addressing follows the rack allocation. Variable addressing uses the relevant slot switches on the IM 306; record the settings of this addressing interface.

On the IM 306, select ON for this 16-channel digital module. The starting byte must be even. For example, decimal 20 = 14H selects weights 16 and 4, giving I 20.0–I 21.7 in English STEP 5 notation. This is an address-plan example, not a fixed address assigned to the card.

Supply, heat and rack installation

Internal current consumption from the 5 V system supply is 5 mA, and typical module power loss is 10 W. When assessing the power supply, account for bus consumption and field-input energy separately.

Catalog ST 50 permits 100% simultaneous input loading per group at 55 °C. Maintain clear airflow in the rack installation, and check mounting requirements and the existing configuration for the fitted rack, such as the 6ES5 700-1LA11.

Differences from similar codes

The 6ES5 431-7LA11 is a 24/48 V UC model, while the 6ES5 430-7LA12 has 32 inputs for 24 V DC. The 6ES5 434-7LA12 is a separate 8-input module with an interrupt group signal.

The 6ES5 435-7LA11 is for 115 V UC inputs. The 6ES5 432-4UA12 belongs to the S5-135U/155U family and provides 32 interrupt inputs for 24 V DC. The number 432 alone does not establish voltage rating, channel count or system compatibility.

Replacement preparation and used-module checks

Back up the program and memory unit, and photograph the connector’s four group commons and existing addresses. Verify both logic states on every channel during testing.

During S5 maintenance, assess group commons, field voltage and address allocation together. For used Siemens modules, state label details, included connector, physical condition and completed tests for the individual item.

Editor’s note

Check the test voltage before calling the card faulty. Logic 1 starts at 30 V on this model. Make sure the source suits this input card before testing channels one by one.

Check the common when four inputs disappear together. A loose N/M connection can affect an entire group. Checking that shared connection first can save unnecessary removal and testing.

Group isolation does not permit different phases. Siemens excludes that connection for this card. Trace the existing supply circuits against the drawing and measurements before reconnecting them.

Look for the address setting in the right place. Fixed slot arrangements and systems using IM 306 are different. Photograph the rack and any IM 306 switches before replacing the module.

Make the final check across every channel. Use a suitable AC/DC test source and check all four groups. Record the green indication, program bit and measured voltage together so that the result remains clear.

OtomasyonAVM resources and PDFs

+ S5-115U manuals and SIMATIC S5 PDF archive

+ S5 digital input modules and model pages

Related topics

+ 6ES5 431-7LA11 – 24/48 V UC input

+ 6ES5 430-7LA12 – 32-channel 24 V DC input

+ 6ES5 434-7LA12 – input with interrupt group signal

+ 6ES5 435-7LA11 – 115 V UC input

+ 6ES5 490-7LB11 – 24-pole front connector

Browse SIMATIC S5

+ Back to S5 digital input modules

+ SIMATIC S5 system pages

+ Siemens S5 PLC main page

+ Used Siemens products and models

Siemens and external references

+ Siemens S5-115U – 432-7LA11 specifications and wiring, 15-23 (English)

+ Siemens S5-115U – fixed slot addressing, 6-2 (English)

+ Siemens S5-115U – IM 306 address switches, 6-5 (English)

+ Siemens ST 50 – input levels and 100% loading, 3/30 (English)

+ Siemens ST 50 – connector and ordering options, 3/31–3/32 (English)