6ES5 763-7LA11
Siemens 6ES5 763-7LA11 S5 Front Connector Jumper Comb
Siemens 6ES5 763-7LA11 is the 763 jumper comb used to common electrical connections in 490 screw-terminal front connectors on SIMATIC S5 systems. It belongs to the connection accessories documented for the S5-115U family. Siemens ST 50 lists a package quantity of 10 jumpers; confirm whether a quotation covers individual pieces or a complete package.
When checking digital input and digital output wiring, identify which terminals the circuit diagram requires to share a potential. This is a passive conductive bridge within the S5 connector wiring. Select its terminal positions from the specific module’s diagram; its placement does not set CPU addresses or program parameters.
Front connector selection and wire size
Siemens lists the screw-terminal versions as the 24-pin 6ES5 490-7LB11 and 46-pin 6ES5 490-7LB21. The 763 comb is an accessory for this connection type. For the 46-pin 490-7LB21 with a bridge jumper, ST 50 specifies a maximum conductor cross-section of 1.5 mm².
6ES5 490-7LA11 and 6ES5 490-7LA21 are separate crimp-terminal versions. Read the complete connector suffix and identify its connection method before selecting the bridge. Do not force a part intended for screw terminals into a different contact arrangement.
Which terminals should be bridged?
There is no universal terminal list for every module. In a cabinet containing a 6ES5 420-7LA11 or 6ES5 430-7LA11, first match the exact module, front connector and electrical drawing. Fit the bridge only where the diagram requires the terminals to form the same electrical point.
When moving to different modules such as the 6ES5 431-7LA11 or 6ES5 432-7LA11, check every connection against that module’s diagram. Copying the old bridge arrangement without this check can unintentionally join separate supply or common-terminal groups.
For a combined I/O module or an output module such as the 6ES5 441-7LA11, record the circuit served by the bridge. If several channels fail together, inspect the common connection for looseness, corrosion or incorrect placement before replacing the module.
Installation and fault checks
Disconnect the power supply and any separate field supplies before working on the connection. Check for absence of voltage at the actual terminals; the indicators on the S5 rack do not establish this. Inspect the bridge teeth, terminal housing and clamping surfaces for damage and contamination.
After installation, check continuity between the intended common terminals and verify that separate groups remain electrically separate. When investigating a group fault with the CPU running, consider the S5 system’s program state alongside its field wiring. A continuity check alone does not prove a sound connection under load.
When buying used S5 supporting accessories, specify the complete order number, actual quantity and physical condition. Look for bent teeth, darkened contact surfaces, significant corrosion and signs of excessive clamping. Connector weight, current ratings and pin counts must not be presented as specifications of the jumper comb itself.
Editor’s note
Give this small bridge a proper inspection. If several channels disappear together, start with their common connection. A loose terminal is worth finding before spending hours replacing a healthy module.
Before removing the comb, photograph its position and terminal numbers, then compare them with the drawing. An existing connection in an old cabinet may have been altered incorrectly during an earlier repair.
Do not try to straighten a bent tooth by tightening the terminal harder. Inspect both the comb and its seating point. A good bridge fitted to a cracked terminal housing still leaves an unreliable connection.
A continuity beep is a useful first check. During controlled operation, also assess the voltage drop across the connection. A poor contact can pass the meter’s small test current yet cause trouble when the circuit is working.
Agree whether the supply is ten individual pieces or one complete package. Keep the catalogue package quantity separate from the seller’s actual stock. Clear photographs and an accurate count make this small accessory much easier to buy correctly.
OtomasyonAVM resources and PDFs
+ 6ES5 763-7LA11 product and information page and Siemens S5 models.
+ 490-7LB11 screw-terminal front connector and 490-7LB21 screw-terminal front connector pages.
+ OtomasyonAVM shared SIMATIC S5 PDF archive.
+ S5-115H system manual, English: 763 jumper comb and 490 front connector table. Printed page 17-61 / PDF page 493.
Related topics
+ S5 cables and connectors, digital input modules and digital output modules.
+ About Siemens S5 PLC and S5 power supplies.
Browse SIMATIC S5
S5 expansion products | S5 cables and connectors | SIMATIC S5 | Siemens second-hand homepage
Siemens and external references
+ Siemens S5-115U system manual, EWA 4NEB 811 6130-02b, Edition 04, English. Printed page 15-66 / PDF page 594: exact 6ES5 763-7LA11 order number and screw-terminal front connectors.
+ Siemens ST 50 catalogue, 1998, English archive copy. Printed page 3/97 / PDF page 179: application, conductor cross-section table and package quantity of 10.