6ES5 101-8UA33

Siemens SIMATIC S5-101U 6ES5 101-8UA33 Central Controller

The 6ES5 101-8UA33 is a compact PLC in the Siemens SIMATIC S5 family with 20 digital inputs and 12 transistor outputs. In existing machines, it reads sensor and position signals, handles timing and counting, and switches 24 V DC loads according to the control sequence.

Power supply and fuses

The controller uses a nominal 24 V DC power supply with an allowable range of 20–30 V DC and a maximum controller current consumption of 0.9 A. The controller supply fuse is 2 A, slow-blow. Each output group has its own FF 10 A load supply fuse.

If one 24 V DC source feeds the controller, output loads and devices such as inductive proximity sensors, size it for their combined current. Figure 13 shows L+/M for the controller supply and L1+/M1 and L2+/M2 for the two output load supplies.

Digital inputs and transistor outputs

The twenty digital inputs are rated 24 V DC and use M3 as their reference. The addresses are I0.0–I0.7, I1.0–I1.7 and I2.0–I2.3. The logic 1 range is +13 to +35 V DC, with typical input delays of 3 ms on and 6 ms off.

The twelve transistor outputs switch the positive supply. The first group covers Q0.0–Q0.5. The second covers Q0.6–Q0.7 and Q1.0–Q1.3. When comparing other S5 I/O layouts, check the group split and common references against the terminal drawing.

Siemens specifies up to 1 A per channel at up to 40 °C and 0.5 A at up to 55 °C. For a contactor or interposing relay coil, also check the manual’s 8 W inductive load limit. A suitable relay interface can provide a dry contact where the circuit requires one.

STEP 5 and program memory

The front PG interface is used for STEP 5 programming and program backup. The internal RAM holds 1,024 statements and supports battery backup. A compatible EPROM or EEPROM memory submodule can retain the program for long-term storage. Siemens lists 6ES5 731-1BD20 as the programming cable for the PG 670 and PG 675.

Expansion and related order numbers

The EU/EG port connects to an S5-101U expansion unit through a short ribbon cable. The 6ES5 101-8UC31 is the expansion unit with a 24 V DC supply and transistor outputs. The 6ES5 101-8UC11 is the expansion variant with relay outputs and a 220/240 V AC supply.

When replacing the central controller, compare the full order number, supply, output type and I/O addresses. The 6ES5 101-8UA13 has 20 inputs and 12 relay outputs, and the 6ES5 101-8UB13 has 10 inputs and 6 relay outputs. The 6ES5 101-8UA23 is the triac-output variant.

Editor’s Note

When testing a used 8UA33, if six outputs fail together while the CPU is in RUN, first check that group’s L1+/M1 or L2+/M2 load supply and FF 10 A fuse. The output LEDs draw power from the load supply. Once both groups have their 24 V DC load supply, test the channels individually with a suitable load. Back up the existing STEP 5 program before resetting the unit or changing its memory submodule.

To sell a used 6ES5 101-8UA33, send the quantity, working condition or fault details, a label photo and your asking price to otomasyonavm@gmail.com.

Related topics

SIMATIC S5-90U | S5-100U CPU 102 | S5-100U CPU 103

Navigation

Shared SIMATIC S5 PDF archive | S5 CPU 90U–115U | Used SIMATIC S5 | Siemens second-hand main page | Second-hand automation

References

Siemens SIMATIC S5-101U Operating Instructions (PDF, EN) · Document EWA 4NEB 810 2119-02c. Terminal assignments in Figure 13, p. 2-7. Supply and memory on pp. 5-1–5-2. I/O ratings on p. 5-4. PG cable on p. 6-1.