6ES5 464-8MD11

Siemens 6ES5 464-8MD11 — Four-Channel ±20 mA Analog Input Module

Siemens 6ES5 464-8MD11 is a four-channel ±20 mA analog input module for SIMATIC S5. It is documented for S5-90U, S5-95U, S5-100U, ET 100U and ET 200U applications. This member of the S5 analog module family supports 1, 2 or 4 active channels, with a nominal measurement resolution specified as 11 bits plus sign.

The module transfers measurements from a compatible current-output pressure transmitter, level instrument or temperature converter to the PLC. In analog measurement applications, check the instrument’s output range and power arrangement alongside its measurement function.

Input range and order-number differences

The bipolar analog signal range is −20 mA to +20 mA. This analog input converts both current magnitude and polarity into a digital measurement. Confirm that the connected instrument provides a current output before wiring it to the module.

8MD11 is a current-input variant. 6ES5 464-8MC11 provides four ±10 V voltage inputs, while 6ES5 464-8ME11 provides four 4–20 mA inputs. Similar order numbers do not establish interchangeability; compare the wiring and scaling used by the application.

6ES5 464-8MB11 is the ±1 V variant, and 6ES5 464-8MF11 is intended for Pt100 / ±500 mV measurements. A Pt100 cannot connect directly to 8MD11. Temperature measurement requires a suitable current-output converter.

Terminals, transmitter power and isolation

For the signal leads of four-wire transmitters, the channel pairs are Ch.0: 3(+)–4(−), Ch.1: 5(+)–6(−), Ch.2: 7(+)–8(−), Ch.3: 9(+)–10(−). When checking cables and connectors, distinguish channel numbers from terminal numbers.

Two-wire transmitters require an external loop supply; this module does not generate 24 V for the instrument. Its own electronics run from the internal 9 V system supply. Check the S5 power supply and transmitter loop supply separately, and follow the manufacturer’s diagrams for two-wire or mixed installations.

The S5-100U specifications give an input resistance of 31.25 Ω for four-wire connections and 125 Ω for two-wire connections. Inputs are galvanically isolated from one another and from the ground reference. Still check grounding, shield termination and electromagnetic interference when investigating unstable readings.

Channel selection and measurement timing

The front operating mode switches select 50/60 Hz interference rejection and 1/2/4 active channels. Single-channel operation uses Ch.0; two-channel operation uses Ch.0 and Ch.1. Integration takes 20 ms at 50 Hz or 16.67 ms at 60 Hz, with an additional 60 ms processing time per channel.

A new measurement is therefore not produced on every PLC scan. The distinction between analog and digital inputs matters when tracking changing signals. Recheck the program’s channel access if you change the active-channel selection.

Raw data, scaling and program checks

The nominal unit scale is −20 mA = −2048, 0 mA = 0, +10 mA = +1024 and +20 mA = +2048. The directly read input word is left-justified: +20 mA appears as 4000h when the low-order status bits are zero. In PLC programming, distinguish nominal units from the unprocessed input word.

A 4–20 mA signal can be measured, but the application must scale the 4 mA lower endpoint accordingly. The block used for analog I/O processing also matters: the S5-90U/95U manual specifies Y=6 for FB 250, while Basic Functions uses KD=7 for FB 30 AE:464 to select bipolar ±2048 representation. Check the block version and supported CPU.

Use the appropriate system manual for S5-90U and S5-95U installations. For distributed ET 100U/ET 200U stations, follow the addressing and configuration requirements of the interface module. A module used in a different system will not necessarily have the same input address.

Troubleshooting and used-module assessment

8MD11 provides no sensor wire-break detection; zero current may be a valid measurement. During PLC troubleshooting, compare actual loop current, the input word and the scaled engineering value. Test every channel with a known current; one successful channel does not establish that all four work correctly.

Editor’s note

My first check on an older S5 panel is always the complete order number. Several modules can look almost identical from the front. Knowing the Siemens S5 system helps, but the label and the correct wiring diagram should guide the replacement.

If the displayed value is zero, give the field circuit a fair check before condemning the card. Verify transmitter power and then measure loop current. No loop current means no useful signal to read. Remember that this variant does not report a broken sensor wire separately.

With a two-wire transmitter, tracing the supply path on paper can save a long search in the cabinet. Photograph existing links before disturbing an older S5 module installation, then compare them with the manufacturer’s diagram.

Before fitting a spare, photograph the operating-mode switches. A different channel setting can leave you looking for measurements that the replacement has not been configured to acquire. It is a small check that often saves a second visit.

For a used module, ask for measurement results on every channel, preferably at several test points. A general “working” description gives you much less to assess. Provide the full order number, required quantity and a clear label photo when enquiring about a replacement.

OtomasyonAVM resources and PDFs

+ About Siemens S5 PLCs and S5 analog modules: system background and input selection.

+ OtomasyonAVM S5 PDF archive: related system documentation. The Siemens manuals listed below provide English instructions for this module.

Related topics

+ 6ES5 464-8ME11 — four-channel 4–20 mA input

+ 6ES5 464-8MC11 — four-channel ±10 V input

+ 6ES5 464-8MB11 — four-channel ±1 V input

+ 6ES5 464-8MF11 — two-channel Pt100 / ±500 mV input

Browse SIMATIC S5

+ S5 analog modules

+ S5 90/110 module group

+ SIMATIC S5 overview

+ Used Siemens equipment

Siemens and external references

+ Siemens S5-100U System Manual — English; pp. 14-46–14-47, wiring and specifications for the exact order number

+ Siemens S5-90U/S5-95U System Manual — English; pp. 15-66–15-71, wiring, switch settings and value representation

+ Siemens ET 200U Distributed I/O Station — English; pp. 7-16 and 8-49–8-50, analog representation and module specifications

+ Siemens ET 100U Distributed I/Os — English; p. 1-5, supported module list

+ Siemens Basic Functions — English section; FB 30 AE:464 and KD=7 parameter description