6ES5 931-8MD11

Siemens 6ES5 931-8MD11 PS 931 Power Supply

The Siemens 6ES5 931-8MD11 is a galvanically isolated PS 931 power supply for S5-95U, S5-100U, ET 100U and ET 200U installations in the SIMATIC S5 range. The front-panel selector sets the input to 115 V AC or 230 V AC. The rated output is 24 V DC at 2 A, with a specified output voltage range of 22.8–25.2 V DC.

The PS 931 converts cabinet mains power into the 24 V DC used by the PLC or distributed I/O station. Depending on the machine wiring, it may supply the CPU, the station interface or field loads on the same circuit. If the PLC powers up but field signals or actuators are missing, use the schematic to trace where the 24 V supply branches.

Which Siemens S5 systems use it?

Siemens lists the PS 931 as an accessory for the S5-95U in the S5 CPU and compact PLC range. Examples in the S5-95U manual include the 6ES5 095-8MA03, 6ES5 095-8MB02 and 6ES5 095-8MC01 compact units.

In an S5-100U with a CPU 100, CPU 102 or CPU 103, use the 24 V current draw for the exact CPU fitted. On a distributed station, trace the supply using the schematic for the interface module, such as the IM 318 CC on ET 100U or the IM 318-B on ET 200U.

The 115 V and 230 V selector settings

The manuals agree on 115/230 V AC, 50/60 Hz and rated input currents of 0.9/0.6 A, respectively. The permissible frequency range is 47–63 Hz. Siemens gives the following permissible voltage ranges in the three system manuals.

+ S5-100U, page 14-5 · 92–132 V AC at the 115 V setting and 187–264 V AC at the 230 V setting.

+ ET 100U, page 2-5 · 86–150 V AC at the 115 V setting and 187–253 V AC at the 230 V setting.

+ ET 200U, page 8-8 · 92–132 V AC at the 115 V setting and 187–253 V AC at the 230 V setting.

The wiring diagram identifies L1, N and PE on the mains side and L+ and M on the 24 V DC side. Check the selector position and the unit label against the manual for the installed system.

Rail mounting and the 24 V load

The PS 931 fits the S5 mounting arrangement with a 35 mm profile rail. Siemens lists the 6ES5 710-8MA11 as 483 mm long and the 6ES5 710-8MA31 as 830 mm long. The power supply measures about 45.4 × 135 × 120 mm and weighs about 500 g. The screw-terminal 700-8MA11 and crimp-terminal 700-8MA21 are bus bases for I/O modules.

Add up the loads actually supplied by the PS 931. Use the schematic to identify sensors on digital inputs, loads switched by digital outputs and field circuits associated with analog modules. If the shared circuit needs more than 2 A, assess a separate field power supply rated for the load.

The similar-looking 6ES5 930-8MD11 PS 930 has a 24 V DC, 1 A output. The 6ES5 935-8ME11 PS 935 uses a 24 V DC input and a 9 V DC output. Check the full order number and output rating when choosing a replacement.

Editor’s note

Record the label and selector position. Before removing the unit, photograph the 931-8MD11 part number and the 115/230 V setting. The 2 A marking applies to the 24 V DC output.

Check the output under load. If the output reads 24 V with no load but dips at startup, inspect the connected loads and S5 wiring separately. Determine whether the voltage drops at the power supply terminals or at the load.

Allow for the short-circuit protection. Siemens specifies electronic power limiting and non-latching shutdown. If the output disappears, check the individual supply branches and their loads. This model has no separate fault LED.

Record how long the supply dip lasts. Siemens specifies 20 ms of ride-through at 187 V AC input and a 2 A load. If the PLC restarts, record the duration of the dip and which loads switched on at the same time.

Ask for a load test on used units. When assessing a used Siemens S5 power supply, ask for a clear label photo and the measured output voltage, together with the AC selector setting and the DC load used for the test.

OtomasyonAVM resources and PDFs

Compare models under S5 power supplies. For the system layout, see About Siemens S5 PLCs.

+ OtomasyonAVM S5 manuals and PDF archive

Related topics

+ PS 930, 24 V DC 1 A power supply and PS 935, 9 V DC output power supply

+ ET 100U IM 318 CC and ET 200U IM 318-B interface module

Browse the S5 range

Used Siemens S5 · SIMATIC S5 · S5 power supplies

Selling this power supply? Send a nameplate photo, quantity, working or fault condition and asking price to otomasyonavm@gmail.com.

External references

+ Siemens SIMATIC S5-100U system manual (English PDF) · PS 931 specifications on page 14-5. Rails and accessories in Appendix D.

+ Siemens ET 100U distributed I/O manual (English PDF) · PS 931 specifications on page 2-5.

+ Siemens ET 200U distributed I/O manual (English PDF) · PS 931 specifications on page 8-8 and mounting on page 3-4.

+ Siemens SIMATIC S5-95U manual (German PDF) · Appendix F lists the PS 931 order number and rail options.