6ES5 314-3UH12
Siemens 6ES5 314-3UH12 – IM 314H S5-150H Interface Module
6ES5 314-3UH12 is the IM 314H interface module for expansion-unit connections in fault-tolerant S5-150H systems of the Siemens SIMATIC S5 family. It works with an IM 304 in the central controller, extending the 16-bit address and 16-bit data bus to the expansion rack through a symmetrical link.
For this S5 interface module, the manufacturer specifies up to 600 m per link from the IM 304 to the final IM 314H. In the SIMATIC S5 system, the central-controller/expansion-unit connection must be assessed together with the hardware layout and line termination.
IM 304 connection and rack arrangement
The 6ES5 304-3UB11 – IM 304 is located at the central controller, with the IM 314H on the expansion-unit side. When reviewing PLC racks and slots, distinguish the central controller from the expansion rack; the manual uses this arrangement for redundant peripheral connections.
For suitable expansion racks such as the EG 185U, compare the connections from both central controllers against the existing system diagram. The manual permits up to four IM 314/314H/314R modules per IM 304 interface. Cable length means the total route to the last module.
Link, cable and termination
In industrial communication terms, this is a symmetrical extension of S5 address, data and control signals. It uses RS-485 electrical signalling; this alone does not establish Modbus or SINEC-L1 protocol support.
The specified S5 cable and connector arrangement uses the 6ES5 721-0xxx0 cable family. When selecting a cable such as 6ES5 721-0BB00, check its code, length, pin assignment and the existing line layout together. The front connections are 50-pin.
The final IM 314H/314R requires a 6ES5 760-0HA11 terminator. Keep it distinct from the 6ES5 760-1AA11 specified for a standard IM 314; similar housings do not establish identical termination arrangements.
The permitted potential difference between units is 7 V maximum, and the manufacturer requires an equipotential bonding conductor. When assessing grounding and electromagnetic interference, check the cable route, shield connections and cabinet bonding together.
Supply and technical specifications
The manufacturer's shared IM 304/IM 314 table specifies a +5 V DC ±5% supply through the rack, with approximately 1 A for the IM 314. Check the power supply and expansion-rack supply under load.
The same table specifies an operating range of 0 to +55 °C and storage/transport at −40 to +70 °C. Cable-length settings are made on the IM 304 in the central controller; the 600 m maximum does not imply identical transfer times for every installation.
Settings and troubleshooting
Alongside the PLC program, record the address plan, module jumpers and IM 304 line settings. P/Q-area allocation and address conflicts form part of the expansion-unit access checks; loading software alone does not change hardware settings.
During PLC troubleshooting, the IM 304 FAULT indicator on the central side provides a useful starting point. The manual lists expansion-unit power loss, a missing terminator, a broken cable and an incorrect S3 setting among its possible causes.
If the PLC CPU runs but an expansion rack cannot be accessed, check the rack supply, associated link and terminator first. Bent pins, loose locking hardware or corrosion on connectors can produce symptoms resembling an interface-board fault.
Related variants and used-module selection
6ES5 314-3UA11 is the standard IM 314, while 6ES5 314-3UR11 is the IM 314R variant. 3UH12 identifies the IM 314H for S5-150H. Match the full order number and hardware revision when selecting a replacement.
The 6ES5 324-3UA12 – IM 324 serves a separate role in the parallel connection between central controllers. When choosing used interface and communication modules, distinguish the 314H peripheral link from the connection between the central controllers themselves.
For used Siemens equipment, inspect the label, board connections and previous repairs. Test peripheral access through both connection paths in a suitable system. Confirming the S5 system architecture against the actual cabinet is fundamental to selecting the right spare.
Editor’s note
Before starting, photograph the cable connections and jumpers. Record which line goes to which central controller. A small record now makes reassembly much easier.
The device at the end of the line is more than an ordinary plug. Check for the 760-0HA11 terminator required by the IM 314H. Do not condemn a working board because a terminator is missing or incorrect.
The 600 m allowance applies from the IM 304 to the end of the whole line. Establish the actual route first, then check the IM 304 setting.
A FAULT indication calls for checks before replacement. Start with expansion-rack power, cable continuity and the terminator, in that order. Narrowing the fault this way saves time and avoids replacing sound components.
In a redundant system, one working path is only part of the job. Under planned maintenance conditions, verify peripheral access through both paths and the intended switchover behaviour. Hand the system back with an observed operating result, rather than relying on indicator lights alone.
OtomasyonAVM resources and PDFs
Start with About Siemens S5 PLC, S5 interface modules and S5 cables/connectors.
The OtomasyonAVM Siemens S5 PDF archive collects our available documents. This model is covered by the IM 304/IM 314 section of the English U Periphery manual below. The exact order-number mapping appears on page 25 of that section.
Related topics
+ 6ES5 304-3UB11 – IM 304: the central-controller-side interface.
+ 6ES5 760-0HA11: the IM 314H/314R line terminator.
+ 6ES5 314-3UA11 and 6ES5 314-3UR11: different IM 314 variants.
Browse SIMATIC S5
S5 interface modules · S5 cables and connectors · SIMATIC S5 systems · Used Siemens equipment
Siemens and external references
+ Siemens SIMATIC S5 U Periphery – 6ES5 998-0PC22, English: IM 304/IM 314 instructions C79000-B8576-C716-02; §1.2.3 redundant peripheral connection, §1.5 specifications, §2.1–2.2 cable length/termination/potential difference, §3 IM 304 FAULT indicators, §5 exact order numbers. The section starts on page 106 of the combined PDF.