6ES5 310-3AB11
Siemens 6ES5 310-3AB11 — IM 310 Distributed Expansion Interface
The Siemens 6ES5 310-3AB11 is an IM 310 interface module installed at the expansion-unit end of an IM 301 distributed connection in SIMATIC S5 systems. It supports remote I/O connection over a total cable run of up to 200 metres using 721 cable. Within the S5 interface range, it serves a parallel connection between racks.
It establishes the data path between the central Siemens S5 PLC and a suitable expansion unit. Assess the module, partner IM, cable and line termination together when selecting S5 cables and connectors.
IM 301 partner and expansion units
The partner is an IM 301-3 — 6ES5 301-3AB13 or, in the appropriate system arrangement, an IM 301-5 — 6ES5 301-5CA12. Record the full rack number too, including EU 183U variants such as the 6ES5 183-3UA12 and 6ES5 183-3UA13, or the EU 185U 6ES5 185-3UA11. Assess compatibility together with the intended I/O types.
721 cable and the total 200-metre limit
One IM 301 can connect up to four expansion units. The 200 m limit applies to the total cable length from the central controller to the last unit, rather than to every individual segment. Include intermediate units and the actual cable route in the calculation.
For separate cabinets, inspect cable shielding, mechanical fastening, and grounding/equipotential bonding together. Route the connection appropriately relative to power cables. Include the remote rack supply and connector contacts in the diagnosis.
Supply and supported I/O modules
The internal supply specification is 5 V ±5%. The IM 301/IM 310 arrangement supports digital and analog I/O and suitable IP modules that do not require page addressing. Check the module list and addressing conditions against the system instructions.
For digital inputs, digital outputs and analog modules, check for duplicate addresses between the central and expansion racks. Physical fit alone does not establish compatibility for every CP or IP module.
Different role from the IM 312
Local centralized expansion uses arrangements such as the IM 300-3 — 300-3AB11 with an IM 312 variant such as the 312-3AB11 or 312-3AB31. The IM 310 is the remote-side partner of the IM 301. Establish that role before choosing a spare from a similar-looking family.
The fixed-cable 312-5CA21 serves another role in suitable centralized EU 184U/187U arrangements. Mark whether the installed board belongs to the central controller, remote expansion or additional local expansion on a connection sketch before replacing it.
Termination and fault checks
The last IM 310 on the remote line must be terminated. Siemens’ IM 301/310 diagrams show the 6ES5 760-0AA11 terminator. Match the termination part to the installed hardware and the relevant manufacturer’s connection drawing.
The IM 310 has no indicators or controls. During PLC troubleshooting, assess the IM 301 indications, remote supply, cable and termination together. Isolate power before removing or installing modules, and record existing connections before making changes.
Editor’s note
Before changing an IM 310 because a remote rack is inaccessible, check the rack supply, incoming cable and line termination. Understanding the shared connection first reduces the chance of meeting the same fault again after fitting another board.
There is no LED on this board to guide you. Record the central-side symptoms and which expansion units disappear. If the first unit works but the following ones do not, start investigating at that transition.
A terminator is a small part that can cause a long investigation when forgotten. Pay particular attention to the end of a line after removing another rack. An open connector may be more significant than it first appears.
Look beyond the cable sheath: inspect pins, connector fastening and previous repairs. On a connection that has worked for years, one loose contact can cause more trouble than a costly electronic board.
When buying a used Siemens module, seek an I/O-access test with a suitable IM 301 and expansion rack where possible. Connector condition matters alongside the label. Stable operation provides better evidence than a single successful connection.
OtomasyonAVM resources and PDFs
+ OtomasyonAVM S5 PDF archive. Consult the distributed-expansion sections of the manufacturer documents below for the IM 301/310 arrangement.
+ S5 interface modules · S5 cables and connectors · S5 digital inputs · S5 digital outputs · S5 analog modules.
Related topics
+ 301-3AB13 partner module · 301-5CA12 · 760-0AA11 termination · 312-3AB11 centralized expansion · PLC troubleshooting.
Browse SIMATIC S5
+ S5 interface modules · SIMATIC S5 · Siemens S5 PLCs · Siemens second-hand main page.