6ES5 605-0UA12
Siemens 6ES5 605-0UA12 PG 605U Handheld Programmer
Siemens 6ES5 605-0UA12 is a PG 605U handheld programmer for SIMATIC S5. Consider it for inspecting and maintaining STEP 5 programs on site. When selecting S5 service equipment, check the complete order number, keypad layout and supplied connection equipment together.
Siemens lists this version for S5-90U, S5-95U, S5-100U, S5-101U and S5-115U. Record the exact target CPU before working on an S5-90U or another S5 CPU. The 6ES5 605-0UA11 requires a 984 line adapter for 90U/95U connections; check UA11 and UA12 connection requirements separately.
STEP 5 programming and display
The PG 605U uses a statement list, known as STL/AWL. Among PLC programming languages, graphical Ladder and FBD display are unavailable on this handheld unit. For PLC programming, identify the statement-list equivalent of your diagram and the operands involved before starting work.
Record reading, editing and writing to the PLC as separate maintenance activities. Note the block number, original instruction and intended result before making a change. Inspect the program section that calls the affected logic rather than making a decision from one isolated instruction.
TTY connection and supply checks
The interface is a serial TTY current loop, with power supplied through the PLC connecting cable. Check the pin arrangement when selecting S5 cables and connectors. Do not identify a similar-looking socket on an interface module or communications module as a programming port without checking its documentation.
Check the S5 power supply and CPU side before attributing a connection problem to the programmer. Inspect for bent pins, loose locking parts and damage where the cable enters the housing. If an external adapter is used, match its complete order number and suitability to the connection documentation.
Temporary memory and block transfer
The buffer holds one block of up to 1023 statements; unplugging the programmer erases its contents. Distinguish S5 memory modules from the programmer’s temporary buffer. Prepare an independent, verified backup to protect the program in the SIMATIC S5 CPU.
Read the source, destination and block number again before transferring. Afterwards, read the affected block back from the PLC and compare it with the intended change. Record the CPU number, modified block and test result; a photograph of the display is insufficient as a program backup.
Field diagnosis and used-unit acceptance
For digital input, digital output and combined I/O faults, match the program address to the actual field terminal. For analog modules, compare the raw value, scaling and physical measurement. A displayed value alone does not establish that the field device is functioning correctly.
Test a used unit intended for an older S5 system with a known-good CPU and cable. Run the manual’s display and keypad checks. A quotation should state the complete order number, physical condition, supplied cables/adapters and the test actually performed.
Editor’s note
Ask to see the rear label before accepting a unit described simply as “PG 605”. Confirm that the suffix is 0UA12 and inspect the supplied cable in the same set of photographs. This makes the contents of the purchase much clearer.
Typing a few numbers is only the beginning of a keypad test. Check SHIFT, confirmation, deletion and cursor keys as well. Note keys that need excessive pressure or register twice; either problem can make instruction entry unreliable.
Write down the affected block and original instruction before starting. During a long fault-finding session, it is easy to lose track of the first change. Prepare the backup and maintenance notes while the original state is still clear.
A working display is only one part of the acceptance check. Read a block from a known PLC as well. If the connection is intermittent, investigate the cable and socket contacts separately, and record which CPU was used for the test.
Start with reading and comparison instead of changing values on a running machine. Prepare a controlled test arrangement if writing is necessary. Identify the motor, valve or output affected by the proposed program change before applying it.
OtomasyonAVM resources and PDFs
+ 6ES5 605-0UA12 product and information page and Siemens S5 models.
+ OtomasyonAVM shared SIMATIC S5 PDF archive, for system documentation. The dedicated PG 605U manual is linked below.
Related topics
+ S5 connection cables, S5 memory modules and the 6ES5 605-0UA11 version.
+ PLC programming, PLC programming languages and about Siemens S5.
Browse SIMATIC S5
S5 supporting equipment | SIMATIC S5 CPUs | S5 models | Siemens second-hand homepage
Siemens and external references
+ Siemens PG 605U Programmer Manual, English. EWA 4NEB 810 1056-02d; connection Table 1-1, specifications and operating principle in Chapter 2, operation and checks in Chapter 4.
+ Siemens S5-90U/S5-95U System Manual, English and S5-100U System Manual, English. See Chapter 7 for STEP 5 representation methods.