6ES5 430-2BA11
Siemens 6ES5 430-2BA11 – ET 200B Electronics Module, 32 Digital Inputs, 24 V DC
Siemens 6ES5 430-2BA11 is an ET 200B electronics module with 32 digital inputs rated for 24 V DC signals, from the SIMATIC S5 generation of ET 200 distributed I/O. It collects on/off signals from the machine and passes their states to the control system. The complete 2BA11 suffix matters when identifying the module and selecting a replacement.
This ET200 digital input module can be considered for signals from inductive sensors, photoelectric sensors, pushbuttons and mechanical switches, provided their output characteristics and wiring match the installation. The 6ES5 prefix does not mean that this device plugs directly into an S5 CPU rack: this particular model uses the ET 200B electronics-block arrangement.
What do the 32 inputs measure?
Each channel reports a discrete state. The distinction between analog and digital inputs is essential: this module does not convert pressure or temperature into a continuous numerical measurement. Thirty-two channel bits correspond to four bytes. This calculation does not establish the actual address space allocated by the installed master, which must be checked separately.
A 24 V marking alone is insufficient when choosing a sensor. Check the PNP or NPN output type, the input reference and the existing circuit drawing together. A dry contact needs a suitable DC source switched through it to the input; a relay contact does not generate a voltage. Take terminal numbers from the drawing for the actual terminal block fitted to the installation.
Power, reference connections and terminal block
24 V DC is the nominal input signal voltage. Select the system power supply with the sensor loads and station requirements in mind. Review PELV supply arrangements and grounding against the control-panel design. If several inputs disappear together, measure the common supply and reference connections before replacing the electronics module.
The ET 200B electronics block and terminal block must be considered separately. A used listing may include only the electronics block; confirm whether the base, field terminals and bus connection are included. Do not select a terminal block from its appearance or the ET 200B family name alone. Check its complete order number, mechanical fit and wiring diagram.
Communication and input addresses
With distributed inputs, the industrial communication path between the field signals and the controller is also part of fault finding. When assessing a replacement in a PROFIBUS installation, compare the original station order number, master configuration and device definition. A shared family name does not establish interchangeability between revisions; the PROFIBUS FAQ provides background on network operation.
If the starting input byte in the PLC program is assigned as n, the logical representation of 32 channels can be illustrated as n.0–n.7, n+1.0–n+1.7, n+2.0–n+2.7 and n+3.0–n+3.7. This is an addressing example, not a fixed factory address. Verify the actual PLC input area, master settings and field-channel order through online monitoring.
Comparison with other 430 modules and fault finding
When comparing similar order numbers such as 6ES5 430-3BA11 and 6ES5 430-4UA11, establish whether the device is an electronics block or a rack-mounted board. An apparently matching channel count or signal voltage does not establish mechanical or system compatibility. A different suffix requires a verified manufacturer replacement relationship and a review of the existing project.
Compare the signal at the input terminal, the local indication and the bit read by the PLC at the same time. If the signal never reaches the terminal, check the sensor and field cable. If it reaches the input but is missing in the controller, investigate terminal contact, the electronics block and station configuration in sequence. When buying a used digital input module, require all 32 channels to be tested individually; one working channel is insufficient.
Editor’s Note
Start with a clear label photograph and read 6ES5 430-2BA11 right through to the last digit. Buying on the strength of “it is a 430” can leave you with the wrong mounting arrangement.
A clean housing is a useful first impression, but inspect the mating contacts, fastening points and any cracks as well. A corroded connection can make a healthy input appear intermittent.
Do not stop after trying one sensor. Switch all 32 inputs in turn and verify the results in the PLC. A local indicator alone does not prove that the controller receives the signal.
Before removing the original module, photograph the station settings, wire labels and terminal-block order number. That small record can save a long search for the correct channel-to-address mapping later.
For a used unit, specify the complete model, quantity, label photograph, working/faulty condition and price. Sales require an invoice; returns are not accepted, and workshop testing is available. To offer a module for sale, send its details to otomasyonavm@gmail.com.
OtomasyonAVM resources and PDFs
+ Browse the 6ES5 430-2BA11 model page and the SIMATIC S5 digital input module range.
+ Use the Siemens ET200 manuals and the shared S5 PDF archive to locate system documentation.
+ Siemens ET 200B Distributed I/O Station – English system manual. This edition covers ET 200B modules with 6ES7 order numbers; it is not an exact-code technical data sheet or an interchangeability approval for 2BA11.
Related topics
+ About Siemens ET200 and About Siemens S5 PLCs.
+ 6ES5 431-2BA11 electronics module and 6ES5 700-2BA11 terminal block. These links identify different components; they do not establish that either is an equivalent module or a suitable base for this device.
Browse SIMATIC S5 and ET 200
+ Siemens ET200 · ET200 digital input modules · ET200 terminal blocks.
+ SIMATIC S5 · Siemens second-hand range · Used digital input modules.
Siemens and external references
+ Siemens ET 200B system manual, Edition 04 – EWA 4NEB 812 6089-02c, English. Reference for family architecture and document scope; numerical limits for the earlier 2BA11 variant have not been taken from this edition.