6ES7 142-4BD00-0AB0

Siemens main menu › SIMATIC S7 › SIMATIC ET 200

Siemens 6ES7 142-4BD00-0AB0 — ET 200pro 4 DO 24 V DC/2 A High Feature

6ES7 142-4BD00-0AB0 is the ET 200pro 4 DO DC 24V/2.0A High Feature digital output module in the Siemens ET 200 distributed I/O family. Its four 24 V DC outputs control suitable solenoid valves, DC contactor coils and indicator lights. This model in the ET 200 digital output range provides channel-specific short-circuit and wire-break diagnostics.

Order number: 6ES7142-4BD00-0AB0
Series: SIMATIC ET 200pro
Version: High Feature (HF)
Outputs: 4 DO
Rated load voltage: 24 V DC, 2L+
Rated channel current: 2 A
Total output current: 6 A up to 40 °C; 4 A up to 55 °C
Connection arrangement: Bus module included; suitable CM IO connection module selected separately

Electronics and field connections are separate components

Within the ET 200 system architecture, ET 200pro separates the electronics from the field connection module. The manufacturer's description for this order number specifies an included bus module, while the I/O connection module is ordered separately. Selecting the correct ET 200 connection components is therefore part of preparing a replacement. This output module is not an independent network interface; assess ET 200 communication options through the station's interface module.

Five checks before selection or replacement

1. Channel current and total load: A 2 A channel rating does not mean that all four outputs can continuously supply 8 A in total. The Siemens manual limits total current to 6 A up to 40 °C and 4 A up to 55 °C. When planning ET 200 power distribution, add the currents of all simultaneously active loads. Outputs must not be connected in parallel to increase current capacity.

2. CM IO and socket assignment: Record the installed connection module's complete reference and pin assignment. For example, CM IO 4 × M12 and CM IO 4 × M12 Inverse must not be treated as identical wiring arrangements. A cable fitting mechanically does not establish that its signal reaches the correct pin. When reviewing ET 200 special-function and expansion module range and accessories, also inspect cables, seals and covers on unused sockets.

3. HF diagnostics: Short-circuit and wire-break information is evaluated per channel, while missing load voltage is monitored at module level. Replacing the module without reading its diagnostic record can leave a cable or coil fault unresolved. Identify the reported channel first, then inspect its wiring, load and connections.

4. Load supply: Output loads are supplied from 2L+. When checking ET 200 power supply components, distinguish successful station communication from the presence of load voltage. If several outputs are inactive, inspect the common supply, fuse and return path as well as the output electronics.

5. Hardware project and substitute values: Compare the exact HF module selection, output addresses, diagnostic parameters and substitute-value settings in the Siemens S7 hardware project. This module supports configurable substitute values, which must suit the machine's intended stopping behaviour. Where actual movement must be confirmed independently of an output command, monitor an appropriate sensor or auxiliary contact through ET 200 digital input modules.

Distinguishing similar order numbers

6ES7142-4BD00-0AA0 offers the same channel count and nominal output current with module-level diagnostics; 0AB0 identifies the HF version with channel diagnostics. 6ES7132-4BD00-0AB0 is a different product in the ET 200S family. When comparing products through the Siemens main menu, check both the 142 / 132 and 0AA0 / 0AB0 distinctions.

Editor's note

Correct selection starts with three details: the full order number, the CM IO connection module and the simultaneous total load. “Four outputs, two amps” is not a complete specification. To retain the HF version's diagnostic capabilities, check the project settings alongside the replacement hardware.

Manuals and PDF documentation

On our Siemens ET 200 PDF and user manuals page, consult the ET 200pro distributed I/O system operating instructions. A5E00335544-AP, 07/2022, section 15.5 covers this HF output module. Use the CM IO pin-assignment tables together with the 6ES7142-4BD00-0AB0 product data sheet; section numbering may differ between manual editions.

Related topics and Siemens navigation

Product family: Siemens main menu  |  SIMATIC S7  |  ET 200 family

Station and field devices: Digital output modules  |  Additional modules  |  PROFIBUS and PROFINET

Technical resources: About ET 200  |  Power supply modules  |  ET 200 PDF manuals