6ES7 193-7AA00-0AA0
Siemens Main Menu | SIMATIC S7 | Siemens ET 200 | PDF Manuals
6ES7 193-7AA00-0AA0 — Siemens ET 200iSP TM-IM/EM 60S Terminal Module
Series: SIMATIC ET 200iSP
Product type: Screw-terminal base for one interface module and one electronic module
Order number: 6ES7193-7AA00-0AA0
6ES7 193-7AA00-0AA0 is the TM-IM/EM 60S terminal module for ET 200iSP stations within the Siemens ET 200 distributed I/O family. It accommodates one IM 152 interface module and one compatible electronic module. Among ET 200 terminal blocks, this version is identified by its IM + EM arrangement and blue screw terminals.
Which modules fit this base?
The interface module occupies the left slot; a compatible electronic module occupies the right slot. The right slot can also accept a compatible watchdog or reserve module. The 2 DO Relay electronic module is excluded. When selecting ET 200 digital output modules, check the output technology and its required terminal base together.
The base does not act as a standalone communication interface. In PROFIBUS DP installations, its 9-pin Sub-D socket provides the PROFIBUS RS 485-IS connection. Communication is handled by the fitted IM; ET 200 communication interface modules and their terminal bases are separate components.
Key technical details
Terminal type: TM-IM/EM 60S, screw connections.
Module arrangement: 1 interface module + 1 compatible electronic module.
Dimensions: 60 × 190 × 52 mm (width × height × depth).
Approximate weight: 235 g.
Wiring: The base can be prewired before the electronic modules are installed.
The Siemens catalogue specifies a terminating module as part of the delivery. Its presence must be checked separately when buying a used unit. This component terminates the station backplane/power bus at the right-hand end; it is not the line-termination resistor in a PROFIBUS connector. Refer to ET 200 additional modules and accessories when identifying missing components.
Selection and replacement checks
1. Match the station family. Within the ET 200 system architecture, ET 200iSP, ET 200S and ET 200SP are separate hardware families. An ET 200 label alone does not establish compatibility.
2. Distinguish similar order numbers. 6ES7193-7AA10-0AA0 is the TM-IM/EM 60C version with spring terminals. 6ES7193-7AB00-0AA0 is the TM-IM/IM base for two interface modules. 6ES7193-7CA00-0AA0 is the TM-EM/EM 60S base for two electronic modules. These differences matter when comparing ET 200 connection modules for a replacement.
3. Check the installed configuration. Compare the IM order number and the right-hand module against the station list in the SIMATIC S7 control system. Replacing a base does not mean different electronics will operate with the existing settings.
4. Identify the power supply separately. ET 200 power supply modules and their terminal bases perform a different role. Do not select a TM-IM/EM 60S solely from the station supply voltage.
5. Inspect its condition. Check slot contacts, screw terminals, side connections, rail locking parts and the terminating module. For hazardous-area use, blue terminals alone are insufficient: module compatibility, enclosure requirements and certification conditions must all be checked.
Editor’s note
The two slots do not perform the same role: this base is arranged for one interface module plus one electronic module. Do not order it as the base for a dual-IM station. For a used assembly, clarify whether the offer includes the base, fitted modules and terminating component. Sending a clear base label and a photograph of the complete station through the Otomasyon AVM Siemens product enquiry page helps identify the required part.
PDF manuals and documentation
For module placement, wiring and terminal compatibility, visit the Siemens ET 200 PDF manuals page and refer to the ET 200iSP documentation. Operating Instructions A5E00247483-04 describe this base in “Terminal modules TM-IM/EM 60S and TM-IM/EM 60C”. Use the documentation that applies to the installed hardware revision before carrying out work.
Related topics and Siemens navigation
Terminal blocks | Digital output modules | Connection modules
Additional modules and accessories | Communication interfaces | Power supply modules
Siemens Main Menu | SIMATIC S7 | Siemens ET 200 | PDF Manuals