6ES7 193-4CK30-0AA0
Siemens main menu › SIMATIC S7 › SIMATIC ET 200
Siemens 6ES7 193-4CK30-0AA0 — ET 200S TM-P30C44-A0 Terminal Module
6ES7 193-4CK30-0AA0 is the TM-P30C44-A0 terminal module for the ET 200S series in the Siemens ET 200 distributed I/O family. It provides the mounting base and supply/field connections for a PM-E F PROFIsafe power module. The power module is a separate component; this order number does not identify a standalone power supply or safety controller.
Type: TM-P30C44-A0
Order number: 6ES7193-4CK30-0AA0
Connection: Spring-type terminals
Terminal arrangement: 2 × 3 + 2 × 4, 14 connection points in total
AUX1: Accessible at terminals, interrupted to the left
Dimensions (W × H × D): 30 × 132 × 43 mm
Approximate weight: 100 g
Which power modules use this base?
Siemens’ assignment table lists PM-E F pm DC24V PROFIsafe and PM-E F pp DC24V PROFIsafe among the ET 200 power supply modules that use this terminal type. Check the full order number and revision of the fitted module before purchasing. A PM-D F or another similarly named power module must not be assumed to use the same base.
The safety function of ET 200 fail-safe modules depends on the appropriate electronics and system configuration. The terminal base does not independently handle PROFIsafe safety communication or establish a SIL or PL rating on its own.
Why the interrupted AUX1 bus matters
On this base, AUX1 has no electrical continuity to the potential group on its left. The AUX1 potential is accessible through terminals A4 and A8. Do not assume that an auxiliary potential from the neighbouring base automatically continues across this boundary.
In the ET 200 power distribution arrangement, the cabinet schematic determines the purpose of AUX1. Do not automatically treat it as 0 V, 24 V or protective earth without checking the design. This distinction matters just as much as the terminal connection method when selecting ET 200 terminal blocks.
Difference from 4CK20 and its role in the station
6ES7193-4CK20-0AA0 is the screw-terminal TM-P30S44-A0; 6ES7193-4CK30-0AA0 is the spring-terminal TM-P30C44-A0. Their shared application does not justify transferring field wiring without checking it. The same principle applies to other ET 200 connection modules: use the full type designation and terminal diagram.
Within the ET 200 system architecture, this base introduces the supply for a new potential group extending to the next TM-P base. Fourteen connection points do not mean fourteen digital channels. The fitted PM-E F module’s outputs and the ET 200 digital output modules supplied within the group must be considered separately.
Five checks before ordering
1. Base and fitted module: Read both labels. Confirm whether the offer covers only the terminal base or also includes the electronic power module.
2. Connection type: Distinguish spring-terminal 4CK30 from screw-terminal 4CK20. Follow the applicable Siemens instructions for conductor size, preparation and termination.
3. Potential group: Verify the AUX1 interruption to the left and the intended function of A4/A8 in the cabinet schematic. Do not add a bridge merely to restore assumed continuity.
4. System compatibility: Check the F-CPU, PM-E F and ET 200 communication interface against the project requirements. A correct terminal base cannot compensate for missing safety configuration.
5. Physical condition: Inspect the spring terminals, side contacts and locking parts for damage or signs of overheating. Identify any required ET 200 additional modules and accessories separately.
Editor's note
Selecting this component requires more than matching “30 mm, spring terminals”. The PM-E F assignment and interrupted AUX1 arrangement must also match. Compare the base label, power module label and wiring diagram before maintenance. After changes to a safety circuit, the relevant safety functions must be verified by qualified personnel.
Manuals and PDF documentation
Use our Siemens ET 200 PDF and user manuals page to consult ET 200S Terminal Modules, A5E01120034-01, section 1.5 together with the manual for the installed PM-E F module. Siemens specifies particular parallel-terminal wiring requirements at high output currents; this overview alone is not a wiring instruction.
Related topics and Siemens navigation
Product family: Siemens automation | SIMATIC S7 | ET 200 family
Safety and power: PROFIsafe | Fail-safe modules | Power supply modules
Connections and documentation: Terminal blocks | Connection modules | ET 200 PDF manuals