6ES7 141-1BF41-0XA0

Siemens 6ES7141-1BF41-0XA0 ET 200X EM 141 Digital Input Module

6ES7141-1BF41-0XA0 is an EM 141 expansion module with 8 digital inputs rated at 24 V DC in the SIMATIC ET 200X family. Part of the Siemens industrial automation range, it collects status signals from proximity sensors and position switches.

This member of the Siemens ET 200 distributed I/O family has eight 5-pin M12 sockets, with one input channel per socket. In machine and industrial automation applications, this arrangement helps identify the channel associated with each sensor cable. Keep the socket number, sensor label and PLC input address together in maintenance records.

Sensor supply: individual and total current limits

For PLC-based control systems, calculate sensor power requirements individually and in total. The Siemens data sheet specifies up to 0.5 A per socket and 1 A total at temperatures up to 40 °C, reducing to 0.4 A per socket and 0.8 A total up to 55 °C. These ratings apply to sensor power. Check the station's overall current limit too; the individual maximum cannot be drawn from all eight sockets simultaneously.

Five checks before selection or replacement

1. Basic module and station configuration: EM 141 operates with an ET 200X basic module. The manufacturer specifies this version for all ET 200X basic modules. When reviewing ET 200 system architecture and module selection, record the installed basic module, expansion sequence and hardware configuration. Compare the complete 6ES7141-1BF41-0XA0 order number on the label before replacement.

2. M12 sockets and pin assignments: Sockets X1–X8 correspond to input channels 0–7. Pin 1 supplies sensor power, pin 3 is the supply return, pin 4 carries the input signal and pin 5 is PE; pin 2 is unused. Check the socket viewing direction against the manual drawing before preparing a cable. Wire colour alone does not establish the correct connection.

3. Signal levels and response time: The specified “1” range is 13–30 V, the “0” range is −3 to +5 V, and input delay is 1.2–4.8 ms in either direction. In SIMATIC S7 control applications, include communication and program cycle times when assessing short pulses. When selecting Siemens PLC and I/O products, verify that the sensor's pulse duration can be captured reliably in the application.

4. Channel LED and software indication: Each channel has a green status LED. Compare indications on HMI operator panels with the physical channel LED and the actual PLC input address. Do not assume that this standard input version provides the channel diagnostics of DIAG models. If the sensor operates but the display does not change, check address mapping and signal wiring separately.

5. IP66/IP67 protection and connections: Fit suitable connectors correctly and seal unused sockets with M12 screw caps to maintain the protection rating. Inspect seals, cable entries and socket contacts. After cleaning or replacing cables, complete any open connections before closing the maintenance job.

PDF manual and connection information

Visit the Siemens ET 200 PDF manuals page for system documentation. Section 7.10 of the ET 200X Distributed I/O Device manual, EWA 4NEB 780601602-06, covers this model, while Table 7-22 gives the M12 pin assignments. For assistance, share a complete label photograph, the basic module order number and the affected input number through Siemens product technical enquiries.

Editor's note: A sensor's power LED does not by itself confirm that its signal reaches the module. After verifying the supply at pin 1, compare the signal change at pin 4, the channel LED and the PLC input bit in sequence. This helps distinguish cable, sensor and address-mapping problems.

Related topics and Siemens navigation

Product families
Siemens main menu  |  Siemens PLC products  |  SIMATIC S7

ET 200 resources
ET 200 products  |  ET 200 system overview  |  ET 200 PDF manuals

Control and assistance
HMI operator panels  |  SCADA systems  |  Siemens product enquiries