6EW1890-6AB

Siemens 6EW1890-6AB Multiple-Output Power Supply

Siemens 6EW1890-6AB is a power supply unit with several DC supply rails. The front connection markings on the inspected example identify +5 V, −5 V, +15 V and −15 V rails. Selection therefore requires checking all supply rails and the connection arrangement required by the equipment, rather than matching a single output voltage.

Its listing within the OtomasyonAVM Siemens SITOP power supply section does not identify it as a standard 24 V DC cabinet supply. As with the other Siemens 6EV / 6EW model pages, the complete order number, unit nameplate and host equipment wiring diagram are the basis for identification. Compatibility with a particular CNC or PLC family cannot be established from the 6EW prefix alone.

Input connections and nameplate checks

The inspected front panel carries L, N and PE input markings. Before connection, check the unit’s own rated input voltage, mains frequency and any voltage selection arrangement. PE is the protective conductor; protective grounding and the DC output 0 V reference must be assessed according to their different functions.

Establish the permitted current for each output and the combined loading conditions. Matching the voltage alone is insufficient. Output current ratings, total power, input tolerance and fuse rating must come from a legible nameplate or manufacturer documentation for this exact code, rather than specifications for another 6EW model.

Output polarity and connector identification

The visible −15 V, +15 V, 0 V, +5 V and −5 V connection markings make polarity an essential part of testing. Assess each positive or negative rail against its designated 0 V reference. Multiple 0 V terminals do not justify adding bridges between terminals or bonding them to PE without the wiring diagram. Do not infer connector pin numbers from a photograph.

Replacement checks also cover mounting points, connector keying, cable clearance and ventilation openings. A conversion using standard DIN rail power supplies requires a separate assessment of all DC rails, connections and any monitoring functions needed by the equipment.

Output measurements and load testing

A qualified technician can use a multimeter to check each DC rail against its designated reference and record the polarity. Follow this with appropriate load testing within documented current limits. A correct reading on one rail does not establish that the other outputs or the complete unit are serviceable.

Check cold starting, operation after warming up and response to load changes separately. Where brief voltage dips or voltage fluctuations are suspected, a multimeter’s average reading is insufficient; inspect the waveform with suitable measurement equipment. Acceptance limits must come from the technical documentation and the requirements of the electronics being supplied.

An output that collapses when connected to the machine may indicate a supply fault, excessive load or a downstream short circuit. If an input fuse opens, establish the fault and the original protection rating before further testing; increasing the fuse rating is not a diagnostic method.

What can be inspected during repair?

After disconnecting power and verifying by measurement that stored voltage has been discharged, inspect connectors for overheating and solder joints for cracking. Electrolytic capacitors can be assessed for capacitance and ESR, and diodes checked using methods appropriate to the circuit. These are general service suggestions, rather than a documented list of recurring 6EW1890-6AB faults or instructions to replace particular components.

When an output deviates, assess the load, connection losses and voltage regulation before changing an adjustment. Linear and switching regulators require different diagnostic approaches. Confirm the internal circuit before identifying the topology, adjustment points or substitute semiconductors.

Similar order numbers and used-unit selection

6EW1890-2AC, 6EW1861-2AB and 6EW1861-3AD have separate model records. Similar order numbers do not establish interchangeability with 6EW1890-6AB. A replacement assessment must compare every output, current capability, connector, mounting detail and any system monitoring connections.

When buying a used power supply, request a clear nameplate, serial or hardware details, connector condition and the actual test scope. No-load measurements, load tests and operation in the host equipment provide different levels of evidence. Describe the condition only in terms of tests that have actually been performed.

Editor’s Note

Start with clear photographs of the 6EW1890-6AB nameplate and every connector. Keep the suffix, housing and wiring arrangement together in the service record. Do not transfer a terminal assignment from another 6EW supply; a wrong rail can damage the equipment being powered.

A +5 V reading is only part of the check. Verify the negative rails and both ±15 V rails against their designated references. Using the chassis as the reference for every measurement can produce misleading conclusions when the grounding arrangement is unknown.

If the unit starts cold but loses voltage after warming up, monitor the load and connector heating together. Record the test current, duration and behaviour of each rail. Establish the current limits before increasing the load.

A capacitor can lose performance without visible swelling; capacitance and ESR measurements can help. Replacing components indiscriminately is still a poor substitute for diagnosis. Measure, narrow down the fault, then repair and reassess every output afterwards.

Use suitable probes and an appropriate isolation arrangement for oscilloscope measurements. Do not short an unknown point through an earth-referenced probe ground, or remove protective earth. Mains-side measurements require a qualified technician with suitable equipment.

For a used unit, inspect discoloured connectors, loose contacts and previous repair work before judging the clean cover. Ask which outputs were tested and at what load. A brief no-load check provides different evidence from sustained operation in the host equipment.

OtomasyonAVM Resources and PDFs

Browse other entries through the Siemens 6EV / 6EW model pages. Use the Siemens SITOP files page for the document archive. No verified Siemens technical data sheet or service PDF for this exact order number was located during this work. General SITOP documents must not be treated as the wiring or repair manual for 6EW1890-6AB.

Related Topics

Multimeter measurements + Protective grounding + Capacitors + Short-circuit checks

Used equipment enquiries: Provide the model, quantity, working/faulty condition, clear nameplate photographs and price. Sales require an invoice; returns are not accepted for used products. Workshop testing can be arranged with an agreed test scope. To offer equipment for sale, send details and photographs to otomasyonavm@gmail.com.

Browse Siemens Power Supplies

Siemens second-hand equipment + SITOP power supplies + 6EV / 6EW models + Used power supplies

Siemens and External References

Siemens manufacturer label and front connection markings — product photograph. The photograph is hosted by Classic Automation. Illegible nameplate values must not be used as technical evidence.

6EW1890-6AB product record hosting the photograph. This is a third-party listing, rather than a Siemens service manual.