6EV3054-0DC
Siemens 6EV3054-0DC Power Supply — 24 V DC / 5 V DC, 25 A
Siemens 6EV3054-0DC is a control-system power supply for SINUMERIK 3 / SIROTEC, converting a 24 V DC input into a 5 V DC / 25 A output. Siemens’ product record confirms these electrical ratings. Assess its role in the internal electronic supply of Siemens automation equipment when selecting a replacement power supply. The 25 A rating applies to the 5 V output.
Section 3.1.2 of Siemens’ SINUMERIK 805SM-TW connection manual also lists the exact 6EV3 054-0DC code as the power supply board for the 24 V version. Our site lists it under Siemens 6EV / 6EW models and SITOP power supplies. When using the general information in About Siemens SITOP, retain this model’s specific SINUMERIK/SIROTEC identity.
Electrical Ratings and Version Differences
Nominal input: 24 V DC. Nominal main output: 5 V DC, 25 A. The calculated main-output power is 125 W; this is not the input consumption. Distinguish input voltage from output current. Assess voltage regulation together with connection losses during load testing.
Siemens identifies 6EV3054-0GC as the successor type. However, the detailed section 3.1.4.2 in the 805SM-TW manual describes -0GC. Its pin assignments, battery arrangement and control connections must not be assumed to apply directly to -0DC. Check the installed unit’s nameplate, revision and machine diagram for auxiliary outputs, adjustment limits and protection thresholds.
Connections and Replacement Checks
Compare the complete order code, board revision, connectors and mechanical arrangement with the original unit. Inspect cables, sockets and power supply accessories for current capacity and contact condition. Distinguish the output 0 V return from protective grounding according to the diagram; do not infer pin functions from appearance.
If the machine does not start, measure whether the 24 V input remains stable under load before replacing the board. Interruptions in external relay or supply circuits, wiring losses and a rack-side short circuit can produce similar symptoms. Do not increase fuse ratings or bypass monitoring connections as a trial repair.
Bench and Load Test Suggestions
After isolation and verification that stored voltages have discharged, begin with visual inspection and multimeter checks. Low output resistance alone does not establish a fault; consider the connected load and capacitors. Initial energization requires confirmed connections and appropriate current limiting.
Examine the output at a low load before increasing it in controlled steps. For example, 5 V at 5 A represents a 25 W load; select load equipment with adequate power and cooling margin. These calculations follow Ohm’s law. Record input voltage, output voltage and load current together, and check voltage fluctuations with an oscilloscope. Testing at the full 25 A requires a suitable fixture and cooling; do not invent acceptance tolerances that the documentation does not establish.
Editor’s Note
A 5 V reading without a load is only a starting point. To find a fault that appears as the supply warms up, record measurements at a consistent load together with temperature. Compare voltage at the supply and at the rack; do not compensate for a worn connector by adjusting the supply.
With the board isolated, inspect power diodes, switching devices, connector solder joints and heat-stressed areas. Replacing a burnt component is the beginning of the repair: investigate the short circuit or connection problem that stressed it. These are troubleshooting suggestions, not a confirmed list of recurring model-specific faults.
Assess capacitors beyond visible swelling. Check capacitance, ESR and leakage, and preserve the required voltage, temperature, ripple-current and ESR characteristics when replacing them. Repeat ripple measurements under load before returning the repaired board to the machine.
If an adjustment is fitted, do not turn it simply because the output falls. First check input stability, connector losses and the load. Raising the output by trial and error with CPU and memory boards connected can cause expensive damage. Review memory backups and any battery condition before removal.
When buying a used power supply, request photographs of the complete code, revision and connections. A useful test record states the input voltage, applied load, operating duration and warm-condition results. “Removed from a working machine” does not replace a controlled load test.
OtomasyonAVM Resources and PDFs
Siemens SITOP files is our common document page. The archived document below is a comparison reference for the 805SM-P system and -0GC successor version; it is not a -0DC connection datasheet.
+ Siemens SINUMERIK 805SM-P — Connection Conditions, English PDF; 05.1994, 186 PDF pages. -0GC power supply description: PDF page 33 / printed page 3-6.
Related Topics
6EV3054-0CC + 6EV3054-0FC + 6EV3054-0GC. These links support version comparison; they do not establish interchangeability.
Browse Categories
Siemens 6EV / 6EW models + SITOP power supplies + Siemens second-hand equipment + Used power supplies
Siemens and External References
+ Siemens SiePortal — 6EV3054-0DC product record
+ Siemens 805SM-TW — 06.1993 connection manual; -0DC listed on printed page 3-2
+ Siemens 805SM-P — original 05.1994 PDF