6ES5 983-2AB11

Siemens 6ES5 983-2AB11 — IP 242A/B connector set, four pieces

Siemens 6ES5 983-2AB11 is a connector set for IP 242A and IP 242B counter modules in Siemens S5 systems. Siemens ST 50 lists four connectors per package. In SIMATIC S5 maintenance, it is used when preparing module front connections or replacing missing or damaged connection parts.

The catalog does not describe four complete cable assemblies. It lists the set alongside 6ES5 242-1AA32 IP 242A and 6ES5 242-1AA41 IP 242B. When buying a used high-speed counter module, check separately which connectors and cables are included.

Module front ports and connector matching

The IP 242A/B manual identifies the module-side ports as follows: X3, 37-pin male Sub-D, carries counter 1–5 inputs and start/stop signals; X4 and X5, 9-pin male Sub-D, serve counter 6 and 7 encoder inputs; X6, 15-pin female Sub-D, carries counter 1–7 outputs.

Match the cable-side connectors to this arrangement. For S5 cable connections, verify contact count, gender and the viewing direction used for pin numbering. Identify the interface connection by its documented function. A 9-pin Sub-D shape does not mean RS-232 here.

Encoder signals and voltage levels

In a high-speed counter application, the connector does not alter the module’s signal requirements. Match encoder power and output type to the intended input. For an incremental encoder, check A/B phases, reference signals and common connections against the module diagram.

Counter 6 and 7 inputs on IP 242A/B use 5 V differential RS-422 signals. A line-driver encoder and a 24 V single-ended output require different electrical arrangements. Verify the encoder output type; fitting a connector does not convert 24 V signals to 5 V. General encoder guidance is useful, but use the module manual for actual pin assignments.

Assembly and cable inspection

Inspect the housing, contacts, retaining screws and any cable restraint. Correct bent contacts, pushed-back pins, cracks or arrangements that place cable strain directly on the contacts. Label and photograph the connections before removal.

Do not substitute generic pin lists for digital input, digital output or combined I/O cards for the IP 242 drawings. Each port has a specific function and numbering scheme. Verify power connections separately from signal wiring.

Addressing and commissioning

The connector set has no PLC address or software parameters of its own. Module addressing, input levels and operating modes belong to the IP 242 hardware and PLC programming project. Replacing a connector is not itself a reason to change those settings.

During PLC debugging, check continuity and unintended shorts with power disconnected and the relevant wiring suitably isolated. Then verify counting and direction using a known signal. Record a successful low-speed check separately from testing the complete application operating range.

Editor’s note

When buying used Siemens connection hardware, establish the exact delivery scope. This number denotes four connectors in the catalog. Do not assess it as four complete cables.

If four pieces are offered, request photographs of all four. Check housings, contacts and retaining parts. Two sound pieces and two damaged pieces do not make a complete usable set.

Establish whether the pin diagram is viewed from the mating face or wiring side. A cable assembled using the wrong view can look tidy while being incorrectly wired. Compare every conductor with the diagram.

If moving the encoder cable changes the count, investigate loose contacts and broken conductors first. A connection fault can make an expensive counter module appear defective.

Do not test a serial-communications cable merely because the connector has nine pins. X4 and X5 are encoder inputs. An unsuitable test cable also makes fault diagnosis less reliable.

For legacy S5 systems, retain a clear connection record. Include the IP module number, X3/X4/X5/X6 port, cable label and pin mapping together. That makes the cable’s purpose clear during the next repair.

OtomasyonAVM resources and PDFs

+ Siemens S5 PDF archive: system and module documents. The manufacturer’s IP 242A/B manual is linked below.

+ 6ES5 983-2AB11 model page and used Siemens S5 models: the connector set and related system parts.

Related topics

+ 6ES5 242-1AA32 IP 242A and 6ES5 242-1AA41 IP 242B: the associated counter modules.

+ Line-driver encoders and encoder output types: signal levels and connection arrangements.

+ S5 cable types and used high-speed counter modules: assess the cable and module separately.

Browse SIMATIC S5

Siemens S5 · High-speed counter modules · Encoders · Second-hand Siemens products

Siemens and external references

+ Siemens ST 50 — SIMATIC S5 catalog, English. Page 4/58: IP 242A/B ordering data; 6ES5 983-2AB11 is identified as “Connector (4 pcs.)”.

+ Siemens IP 242A/242B Equipment Manual — 6ES5 998-0KM21, Release 02, English. Section 2.6: X3–X6 ports and pin assignments; Chapter 10: electrical specifications and connection information.