6ES5 243-1AA11
Siemens 6ES5 243-1AA11 — Fully Configured IP 243 High-Speed Analog Module
The Siemens 6ES5 243-1AA11 is the fully configured IP 243 analog module for SIMATIC S5. It includes an eight-channel 12-bit A/D converter, three D/A converters, 8 digital inputs and 8 digital outputs. A/D conversion takes up to 35 µs. Within the S5 analog module range, it combines fast acquisition, signal conditioning and configurable analog signal paths.
There are five physical analog output points, AO1–AO5; these do not represent five independent D/A converters. Their signal sources depend on the board’s internal connections. As an S5 function module, the IP 243 combines measurement, comparison and output functions for analog applications and suitably programmed PLC-based closed-loop control.
Eight-channel high-speed analog input
Jumpers select −5 to +5 V, −10 to +10 V or 0–10 V. An eight-channel multiplexer feeds a single A/D converter. 35 µs is the conversion time, not the complete eight-channel application cycle including software and communications. Match the analog signal, jumper setting and program scaling.
Four separate conditioning circuits provide operating-point and gain adjustment. The module also includes two comparators and two difference amplifiers / P controllers. Connections between these functions are made at the soldering base, so a used board’s existing signal paths can directly affect its behavior.
Three D/A converters and five output points
DAC1 and DAC2 provide ±10 V with 11 bits plus sign. DAC3 provides 8-bit 0–10 V and needs the appropriate analog output amplifier for driving a load. Depending on the connections, AO1–AO5 can carry signals from the converters, conditioning circuits or difference amplifiers.
Write DAC1 and DAC2 using word access. DAC3 is not initialized to a defined value at power-up; the application must write the required initial value. Check startup behavior whenever the output supplies a command to a drive or another process device.
Digital I/O and comparator functions
The module has 8 digital inputs at 24 V DC and 8 outputs switching to the positive supply. Nominal output current is 200 mA per channel, with 600 mA maximum total switching current. When comparing it with S5 digital input and S5 digital output cards, remember that IP 243 outputs are not automatically disabled by BASP and have no individual current limiting.
The card can combine digital I/O states with analog comparison. Interrupt connections depend on the CPU; some installations require a separate interrupt-capable input module and external wiring. Its P-controller circuits do not by themselves constitute a complete PID controller.
Power, connections and system compatibility
The external supply is 24 V DC, with a permitted range of 20–30 V DC. Typical consumption is 600 mA from the internal 5 V rail and 270 mA from the external 24 V supply; the latter excludes sensor supply and digital load currents. Check the S5 power supply capacity accordingly. Analog and digital signals are not galvanically isolated.
On the 43-position front connector, pin 2 is +24 V, pins 34–41 are AI0–AI7, and pins 28–32 are AO1–AO5. Connect analog reference and Mext points according to the complete diagram. When checking S5 cables and connectors, distinguish analog and digital references.
The manual specifies suitable placements in Siemens S5 PLC systems including S5-115U/H, S5-135U and S5-155U/H; an adapter casing is required for S5-115U. S5-150U/S operation requires a suitable expansion arrangement rather than direct insertion into the central rack. Review S5 interface modules and interrupt wiring when checking an expansion installation.
STEP 5 access and variant checks
For PLC programming, FB160 / PER:ANL handles reading and FB161 / PER:ANS handles writing. Direct access selects the channel at base address +7; conversion is started and the result read at +6. Since +7 also contains LOG/STR controls, preserve their intended states during channel selection. During troubleshooting, check BGKN, the selected range and NORM.
The 6ES5 243-1AB11 is an A/D-focused partial configuration; the 6ES5 243-1AC11 is D/A-focused. Neither provides all functions of the fully configured 1AA11. For replacement by a 6ES5 243-1AA12 or 6ES5 243-1AA13, review the complete part number, hardware revision, signal connections and software together.
Editor’s note
The label is only the starting point on this card. Take clear photographs of the soldered links and connection bases before changing anything. Two boards with the same part number may have served different machines with different internal signal paths.
Five analog output points do not mean five separate software-controlled converter channels. Establish which converter or amplifier feeds each point first. That simple map can save a great deal of unnecessary fault-finding.
If a reading has drifted, leave the trimmers alone until the source, reference connection and jumper settings have been checked. Record the existing adjustments before making changes. A small turn made too early can create a much larger calibration job.
For a used card, checking the A/D section is a useful start. Continue with both bipolar D/A channels, the 8-bit output, the analog paths in use and the digital I/O. Knowing exactly what was tested is part of knowing the condition of the board.
Keep the program backup and connection photographs together when preparing a spare. During the first trial, watch the device receiving the output as well as the measured voltage. A carefully verified signal path is the foundation of a reliable replacement.
OtomasyonAVM resources and PDFs
+ Browse the S5 analog modules, S5 function modules and Siemens S5 model pages for related hardware and controller families.
+ OtomasyonAVM S5 PDF archive and system manuals. For IP 243 connections and programming, use chapters 2, 3, 5, 6 and 7 of the English manufacturer manual below.
Related topics
+ 243-1AB11 — A/D-focused partial configuration · 243-1AC11 — D/A-focused partial configuration · 243-1AA12 · 243-1AA13.
Browse SIMATIC S5
+ S5 analog modules · S5 function modules · SIMATIC S5 · Siemens second-hand main page.
Siemens and external references
+ Siemens IP 243 Analog Module with FB160/FB161 — English; 6ES5 998-0KF21, R02/92. Full/partial configurations: 2-1/2; analog input: 3-3/6; outputs: 3-7/10; connector: 5-1/2; specifications: 6-1/5; programming: chapter 7.
+ Siemens migration guide from S5 to S7-1500 — English; 105106251, V1.0, 04/2015, page 48. It identifies 6ES5 243-1AA11 as the fully configured IP 243 and does not specify a direct counterpart in that dated table.