IC694MDL753

IC694MDL753 DC Positive Logic Output Module: Powerful and Flexible Solution

The IC694MDL753 is a 12/24 Volt DC positive logic output module with a capacity of 0.5 Amps per point, offering a total of 32 output points. These points are divided into four isolated groups of eight outputs each, with each group having its own common terminal. As a positive logic module, it switches loads on the positive side of the power supply and supplies current to the load. The outputs can switch user loads over the range of +12 to +24 VDC and can source a maximum of 0.5 Amps per point.

Each group’s I/O connectors have two common pins, each capable of handling 3 Amps. It is recommended to connect both pins for common connections, especially in high-current applications where the current is between 3 and 4 Amps.

Each group can drive different types of loads. For instance, three groups may drive 24 VDC loads, while the fourth group can be reserved for 12 VDC loads. Power for the loads must be supplied by the user, and the module draws minimal power from the user supply to provide gate drive to the output devices. Opto-couplers on the module provide backplane isolation between the field side and logic side.

All 32 outputs are forced OFF when the CPU is stopped. No special fault or alarm diagnostics are provided. Individual numbered LEDs indicate the ON/OFF status of each output point.

Technical Specifications

    Rated Voltage: 12/24V DC, positive logic
    Output Voltage Range: 10.2 to 28.8V DC
    Outputs per Module: 32 (four groups of eight outputs each)
    Isolation: 250 VAC continuous (Field to Backplane); tested up to 1500 VAC
    Group-to-Group Isolation: 50 VAC continuous; tested up to 500 VAC
    Output Current: 0.5 Amps maximum per point, 4 Amps maximum per group, 3 Amps maximum per group common pin
    Inrush Current Capacity: 5.4 Amps for 10 ms
    On-State Voltage Drop: 0.3V DC maximum
    Off-State Leakage Current: 0.1 mA maximum
    Response Time: Maximum 0.5 ms (both ON and OFF)
    Power Consumption:
        260 mA maximum from the 5V backplane bus (13mA + 3mA per point ON + 4.7mA per LED)
        16.5 mA maximum per group from the user supply at 24VDC (all outputs ON)
        9.6 mA maximum per group from the user supply at 12VDC (all outputs ON)

Wiring and Connections

Connections to the output circuits are made through two 24-pin male connectors (Fujitsu FCN-365P024-AU) located on the front of the module. The module’s connectors can be directly wired to field devices using cables with a mating female connector on one end and stripped and tinned wires on the other. Pre-wired cables such as IC694CBL327 and IC694CBL328 can be used, or custom cables can be built. These cables can also be used to connect the module to DIN-rail-mounted terminal blocks.

For high-current applications where the total current for a group exceeds 3 Amps, it is required to use both VIN pins by adding a second wire, ensuring efficient current handling.

Recommendations

The IC694MDL753 module provides reliable and flexible control with its positive logic output features. For high-current applications, it is recommended to connect both common pins to handle the required current. This module is an ideal solution for industrial automation systems where different types of loads must be controlled, offering flexibility at the group level to accommodate varying voltage requirements.


>> IC694MDL753 Output modules User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: GE Fanuc IC694MDL753 Output modules and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."