IC694MDL654

IC694MDL654: 5/12 Volt DC (TTL) 32-Point Positive/Negative Logic Input Module

The IC694MDL654 module provides 32 discrete TTL voltage threshold input points, arranged in four isolated groups of eight inputs each, with each group having its own common terminal. The inputs can be configured for either positive or negative logic and operate at voltage levels up to 15V.

A single regulated +5V supply (current limited to approximately 150mA) is available through the I/O connectors on the front of the module. This supply is generated within the module and is isolated from the backplane. The power input comes from the +5V logic supply on the PLC backplane. By installing jumpers on the I/O connector, you can choose to power the inputs using this internal supply instead of an external user-supplied source.

This module does not report special fault or alarm diagnostics. Green LEDs indicate the ON/OFF status of each input point. The blue band on the front label shows that the MDL654 is a low-voltage module. It can be installed in any I/O slot in the RX3i system.
Technical Specifications:

   Rated Voltage: 5 to 12 volts DC, Positive or Negative Logic
   Input Voltage Range: 0-15 volts DC
   Inputs per Module: 32 (four groups of eight inputs each)
   Maximum Cable Length: 98.4 feet (30 meters)
   Isolation:
        Field to Backplane and Frame Ground: 250 VAC continuous, 1500 VAC for one minute
        Group to Group: 50 VAC continuous, 500 VAC for one minute
   Input Current:
        At 5V: Typically 3.0 mA
        At 12V: Typically 8.5 mA
   Input Characteristics:
        On-state Voltage: 4.2-15 volts DC
        Off-state Voltage: 0-2.6 volts DC
        On-state Current: Minimum 2.5 mA
        Off-state Current: Maximum 1.2 mA
        On Response Time: Maximum 1 ms
        Off Response Time: Maximum 1 ms
   Internal Power Consumption:
        Maximum 195 mA from the +5V bus on the backplane (29 mA + 0.5 mA/point ON + 4.7 mA/LED ON)
        Maximum 440 mA from the +5V bus (if the module's isolated +5V supply is used to power the inputs with all 32 inputs ON)
        Typical 96 mA from the user input supply at 5VDC with all inputs ON
        Typical 272 mA from the user input supply at 12VDC with all inputs ON
   Isolated +5V Supply: 5 volts DC ±5%, current limited to 150mA

Input Points vs. Temperature:

The number of input points that can be ON simultaneously depends on the ambient temperature.


Wiring:

Connections are made using two 24-pin male connectors (Fujitsu FCN-365P024-AU) on the front of the module. Conventional TTL wiring practices should be followed during installation. To ensure noise immunity, I/O control lines connected to the module must be less than 30 meters in length.

Note: If the 24V OUT pin is used to power field devices, the isolation specification changes to:

   Field to Backplane and Frame Ground: 50 VAC continuous, 500 VAC for one minute.

Summary:
The IC694MDL654 is a versatile 32-point TTL input module that supports both positive and negative logic configurations. It is ideal for low-voltage applications and provides fast response times, making it a reliable input solution for industrial environments. With flexible power supply options and compatibility with various input devices, this module offers a robust solution for TTL-based systems.

>> IC694MDL654 input modules User manual (pdf)

++ Other 90-30 PLC modules

----------

+ Ge-Fanuc 2 Homepage

+ Ge-Fanuc Contact (for Automation Mall)

+ About Ge-Fanuc

Reminder: GE Fanuc IC694MDL654 input modules and other Ge-Fanuc modules are available for sale at Otomasyon Mall. Please note that some of the devices are used products, so take this into consideration when purchasing. However, once products are out of stock, new ones will not be restocked. The information above is based on general knowledge and does not guarantee accuracy. For more detailed and precise information, it is recommended to refer to the relevant device’s user manual. 06.03.2013 

"Please note: The user manuals, commissioning suggestions, error codes, and solution recommendations provided on this page are not binding. The information and documents above are open to and even in need of improvement. As the Otomasyon Mall Community, we gladly welcome your suggestions and contributions. If you have field experience and insights on ease of use, please do not hesitate to share them with us."