IC694APU300
IC694APU300 High-Speed Counter Module: High-Performance Counting Up to 80 kHz
The IC694APU300 is a high-speed counter module designed to directly process pulse signals up to 80 kHz. This module senses input signals, processes counting information, and controls outputs independently, without requiring communication with a CPU. It provides fast, real-time control in applications that need precise counting at high speeds.
The module uses the following memory in the CPU:
16 bits of discrete input memory (%I)
15 words of analog input memory (%AI)
16 bits of discrete output memory (%Q)
The High-Speed Counter can be configured for the following:
4 independent, simple counters
2 independent, more complex counters
1 complex counter
Two green LEDs indicate the module’s operating status and configuration parameters. Other key features of the module include:
12 positive logic (source) inputs with selectable input voltage range of either 5VDC or 10-30VDC
4 positive logic outputs
Counts per timebase register for each counter
Internal diagnostics
Removable terminal board for field wiring
The inputs can be used for counting signals, direction control, disable functions, edge-sensitive strobe, and preload inputs, depending on the type of counter selected by the user. The outputs can drive indicating lights, solenoids, relays, and other devices.
The module draws power from the 5VDC bus on the backplane, while input and output power must be supplied by the user or by the +24VDC isolated output from the power supply. The module also provides a selectable threshold voltage, allowing the inputs to respond to either 5VDC or 10-30VDC signal levels.
The blue bands on the label indicate that the APU300 is a low-voltage module. It can be installed in any I/O slot within an RX3i system.
Technical Specifications
Input Voltage Range:
5VDC (TSEL jumpered to INCOM)
10-30VDC (TSEL open)
Positive Logic Inputs: 12
Output Voltage Range: 10-30VDC @ 500mA max, 4.75-6VDC @ 20mA max
Output Protection: Outputs are short-circuit protected by a 3A pico fuse common to all 4 outputs
Power Consumption: 250mA from the 5V bus on the backplane
Isolation:
250VAC continuous between field and backplane, tested up to 1500VAC
250VAC continuous between groups, tested up to 1500VAC
Field Wiring
All inputs for the APU300 are single-ended positive logic (source) type inputs. The high-speed counter inputs can directly interface with transducers using CMOS buffer outputs (74HC04 equivalent) when using the 5V input range. Transducers with TTL outputs should include a 470-ohm pull-up resistor for compatibility with the inputs. For higher voltage open-collector outputs, a 1K-ohm pull-up resistor to +12V is required.
To enable the 5VDC threshold, a jumper should be placed between the appropriate terminals on the detachable terminal board connector. Leaving the terminals unconnected will default the input range to 10-30VDC.
Caution: Do not connect 10-30VDC to module inputs when the 5VDC input range is selected, as this could damage the module.
Terminal Assignments
The table below shows the terminal assignments based on the selected counter type:
Terminal Signal Name Counter Type A Counter Type B Counter Type C
1 I1 A1 A1 A1
2 I2 A2 B1 B1
3 I3 A3 A2 A2
4 I4 A4 B2 B2
5 I5 PRELD1 PRELD1 PRELD1.1
6 I6 PRELD2 PRELD2 PRELD1.2
7 I7 PRELD3 DISAB1 DISAB1
8 I8 PRELD4 DISAB2 HOME
9 I9 STRB1 STRB1.1 STRB1.1
10 I10 STRB2 STRB1.2 STRB1.2
11 I11 STRB3 STRB2.1 STRB1.3
12 I12 STRB4 STRB2.2 MARKER
13 INCOM Common for inputs INCOM INCOM
14 OUTPWR DC+ for outputs OUTPWR OUTPWR
15 TSEL Threshold select (5V or 10-30V) TSEL TSEL
16 O1 Positive Logic Output OUT1 OUT1.1
17 O2 Positive Logic Output OUT2 OUT1.2
18 O3 Positive Logic Output OUT3 OUT1.3
19 O4 Positive Logic Output OUT4 OUT1.4
20 OUTCOM Common for outputs OUTCOM OUTCOM
Recommendations
The IC694APU300 High-Speed Counter Module is ideal for industrial applications requiring fast and precise counting. It offers high-speed processing, real-time control, and flexible configuration options. The ability to switch between different voltage ranges and counter types makes it highly adaptable to various automation systems. For high-speed signal processing needs, this module provides reliable and independent performance without CPU intervention.
>> IC694APU300 input modules User manual (pdf)
----------
+ Ge-Fanuc Contact (for Automation Mall)