What is an LED (Light Emitting Diode)?
What is an LED (light emitting diode)?
Dear colleagues,
LED stands for Light Emitting Diode. It is a semiconductor diode that produces light when a suitable current flows in the forward direction. LEDs are used in indicators, general lighting, optical sensing and display backlighting.
Light is generated by electron-hole recombination in the semiconductor's active region, a process called electroluminescence. The directly emitted colour depends on the semiconductor's properties. The colour of the outer package alone does not reliably identify the emitted light.
Anode and cathode: which way should an LED connect?
The anode — A and cathode — K are the two basic terminals. During normal forward operation, the anode is more positive than the cathode. Conventional current flows from anode to cathode. An ordinary single-die LED normally does not emit light when reverse biased, but exceeding its reverse voltage limit can damage it.
On some leaded LEDs, the longer lead identifies the anode and the shorter lead identifies the cathode; a flat package edge may also mark the cathode. However, trimmed leads, different packages and multi-terminal LEDs make these clues insufficient on their own. Follow the manufacturer's pin drawing, especially for SMD, RGB and multi-die devices.
Forward voltage and emitted colour
Forward voltage — VF is the voltage drop across an LED at a specified forward current. It varies with colour, semiconductor material, temperature and current; there is no single value for every LED. Read the data sheet value together with its current and temperature test conditions.
A common white LED design combines a blue-emitting die with phosphor that converts part of the light into other wavelengths. An RGB LED uses separately controlled red, green and blue channels to create different colours. Common-anode and common-cathode devices require different connections.
Why does an LED need a resistor or current driver?
Small voltage changes can cause substantial changes in LED current. Therefore, a bare LED should not connect to a voltage source without current limiting. A series resistor is often suitable for a small indicator, while higher-power applications may use an appropriate constant-current driver.
Using Ohm's law, an approximate resistor value is R = (Vsupply − VF) / IF. With a 5 V supply, an assumed 2 V forward drop and a target current of 10 mA, the result is 300 Ω. Choosing 330 Ω gives approximately 9.1 mA and about 0.027 W of resistor dissipation. These are example calculations; check tolerances, temperature and the LED's permitted current separately.
Animation: how an LED produces light
The red h⁺ symbol represents holes and the blue e⁻ symbol represents electrons. The arrows illustrate carrier injection towards the active region. Radiative electron-hole recombination emits photons; not all input energy becomes light.
Each illustration cycle lasts 600 + 600 + 200 ms, or 1.4 seconds. The stages are separated for explanation; a real LED emits light while a suitable forward current continues. Colours and semiconductor structure are illustrative, and current limiting circuitry is omitted.
12 V LEDs, 24 V LEDs and driver circuits
A “12 V LED” or “24 V LED” often refers to the supply rating of a product containing resistors, series-connected LEDs or driver circuitry. It is not the forward voltage of a single bare LED die. A constant-voltage module and an LED string requiring constant current need different supply arrangements. Determine the appropriate DC voltage or current from the product's technical information.
An LED driver may contain an integrated circuit and, depending on its topology, capacitors and inductors. A MOSFET or transistor may provide external switching. Total wattage alone is insufficient for driver selection; current, output voltage range and dimming method must also match.
How is brightness controlled?
Brightness can be adjusted by changing current within the permitted limits or by using PWM — pulse-width modulation. PWM switches the LED on and off at a defined on-state current; duty cycle influences average light output. A microcontroller can generate PWM, with a suitable driver where required. PWM does not remove the on-state current limit.
PWM frequency, driver response and application requirements must be considered together. Rapid light variations can produce camera banding or flicker effects even when they are not obvious to the eye. LEDs and their drivers do not all have the same switching behaviour; a single nanosecond figure cannot describe every product.
Do LEDs generate heat, and what determines lifetime?
LEDs generate heat. A light beam carrying less heat does not mean the LED die remains cool. High-power LEDs especially need a suitable thermal path through the board and heat sink. Junction temperature, drive current and thermal design influence light output, colour stability and useful life.
A figure such as “25,000 hours” does not apply to every LED. Lifetime information needs a defined criterion and operating conditions. For example, L70 relates to light output declining to 70% of its initial value; it does not mean the LED necessarily stops emitting light at that point. The driver, connections and other lamp components can also limit product life.
How should LEDs be assessed in lighting and automation?
Watts describe electrical power consumption, while lumens describe total visible luminous flux. lm/W helps compare luminous efficacy. Colour temperature, expressed in kelvin, describes the warm or cool appearance of white light; CRI describes a separate aspect of colour rendering. Higher wattage alone does not establish greater output or better light quality.
An LED on a PLC or another industrial device may indicate status. In optical sensors, an LED can act as the emitter while a photodiode detects the received light. An optocoupler typically uses an infrared LED to transfer a signal across an electrically separated interface. An illuminated indicator does not prove that the complete system is operating correctly.