6ES7 193-1CL00-0XA0
Siemens 6ES7 193-1CL00-0XA0 — ET 200L TB 32L screw-type terminal block
Siemens 6ES7 193-1CL00-0XA0 is the 32-channel TB 32L terminal block with screw connections for ET 200L stations in the SIMATIC ET 200 family. It supports the electronics block and carries the fixed field wiring. Sensor, load and supply conductors terminate at this part of the station.
The TB 32L is not a standalone PLC or a complete working I/O station. A compatible electronics block is required to read inputs or control outputs. When identifying a replacement, record the order number of the terminal block separately from the number on the electronics above it.
Construction and cabinet space
The defining features are the TB 32L format, 32-channel arrangement and screw-type conductor connections. Siemens gives the terminal block dimensions as 191 mm wide, 100 mm high and 40.5 mm deep. Cabinet planning must also allow for the electronics block, communication connector, cable bends and access for maintenance.
The separation between wiring and electronics is an important part of the ET 200 system structure. Replacing the electronics and replacing the terminal base are different jobs. A base replacement requires the field conductors to be disconnected and restored to their correct positions, making a reliable terminal record particularly useful.
Electronics block compatibility
The Siemens assignment table lists 6ES7131-1BL01-0XB0 — 32 DI, 6ES7132-1BL00-0XB0 — 32 DO and 6ES7133-1BL01-0XB0 — 16 DI/16 DO for TB 32L. Check the complete order number and version of the installed equipment before replacement.
These options give the station different functions. Do not transfer a wiring arrangement from a digital input station to a digital output station merely because the bases look alike. Signal requirements and load limits are determined by the electronics.
32 channels do not mean 64 independent I/O points
The TB 32L connection table assigns terminals 1–32 to signals. The functions of terminals 33–64 depend on the electronics and include sensor supply or output-circuit common connections. Numbering that reaches 64 therefore does not indicate 64 independent input or output channels.
Supply and common terminals have different jobs from signal terminals. Power reaching the electronics does not establish that every field circuit is correctly supplied. Trace the circuit from the power supply through the relevant group feed to the connected device. When checking the power distribution arrangement, use the station drawing to identify linked terminals and separately supplied groups.
M / 0 V and protective earth PE have distinct functions. Do not bridge them on the basis of terminal numbering or conductor colour. The grounding and reference-potential arrangement must follow the cabinet design and manufacturer’s instructions.
Connecting sensors and output loads
For any sensor connection, first establish the electrical requirements of the installed input electronics. An inductive sensor or photoelectric sensor must have a compatible supply, output circuit and common connection. The terminal base does not change PNP/NPN or sinking/sourcing compatibility.
With connector cables, trace each sensor pin to its numbered cabinet termination. Wire colours may have been reused or changed during previous repairs. Labelling conductors, photographing the assembly and checking the drawing before disconnection makes a base replacement easier to verify.
For outputs driving an interposing relay, valve or contactor coil, check the load current and suitable suppression. Output current ratings, short-circuit behaviour and switching capability belong to the electronics block. They cannot be established from the TB 32L order number alone.
Installation and screw-terminal checks
Place the machine in a safe condition, isolate the relevant energy sources and verify that the circuit is de-energized before starting work. Inspect the rail attachment, electronics-block seating area, contacts and conductor clamps. A cracked housing, broken retaining feature or damaged contact should not be accepted simply because a wire can still be connected.
A sound screw-terminal connection depends on conductor size, construction, stripping length and tightening torque. Follow the applicable ET 200L instructions. The clamp must grip the conductor rather than its insulation, and loose strands must not reach neighbouring terminals. Where ferrules are used, their preparation must suit the terminal’s approved conductor requirements.
Before recommissioning, check the DIN-rail power supply, circuit fuses, group feeds and field wiring together. A detachable electronics block does not by itself establish permission for replacement under power. Follow the replacement procedure for the installed system.
Separating base faults from electronics faults
If the station communicates but one channel does not operate, start with that channel’s field wiring and supply. When several channels fail together, investigate shared supply and return paths as well. Loose conductors, oxidised contacts, overheated terminals and an incorrectly seated electronics block can produce similar symptoms. Use measurements to narrow down the fault before deciding which component to replace.
A station that disappears completely also requires checks of the PROFIBUS connection, station supply and electronics. A new terminal block will not correct an address or project mismatch. Equally, successful communication does not prove that every load circuit is correctly wired.
Related versions and the supplied assembly
6ES7193-1CL10-0XA0 is the spring-terminal TB 32L version. 6ES7193-1CH00-0XA0 is the screw-terminal TB 16L. Select by the full order number, connection method and channel arrangement. Similar-looking connection components should not be assumed interchangeable.
Supplementary terminals are accessories rather than replacements for the main base. Check whether the listing includes the required additional accessories, electronics block and communication connector. For a used item, photographs should clearly show the screws, contacts, rail attachment and electronics-block seating area. Refer to the individual seller’s description for inspection or test status and the components supplied.
Editor’s advice
The most time-consuming part of a TB 32L replacement is often reconstructing a wiring arrangement that was not recorded before removal. Label the conductors first, then disconnect them. Photograph both the base and electronics-block order numbers. If an overheated connection prompted the replacement, inspect the conductor end and connected load too. Moving damaged wiring onto a new base can leave the original problem unresolved.
Technical references and user manuals
Identification and dimensions were checked against the Siemens product data sheet; electronics assignments and terminal functions were checked against the ET 200L system manual. Use the Siemens ET 200 PDF and user manuals page to locate the relevant ET 200L documentation. The wiring diagram must match the complete order number of the installed electronics.
Related topics
ET 200 terminal blocks / Digital input modules / Digital output modules / Power distribution components / Sinking and sourcing
Navigation: Siemens automation > SIMATIC S7 > Siemens ET 200 > ET 200 manuals