6ES7 182-0AA01-0XA0

Siemens 6ES7 182-0AA01-0XA0 – IM 182-1 PROFIBUS-DP PC Slave Board

Siemens 6ES7 182-0AA01-0XA0 is the IM 182-1 PC slave board, designed to connect an ISA-based computer to PROFIBUS DP. It represents the computer as a slave station and supports transmission rates of up to 12 Mbit/s. The board is relevant when maintaining existing PC applications that use Siemens communication interfaces.

The required network role is an essential selection criterion. In a master/slave arrangement, IM 182-1 operates on the side accessed by the master. If the computer must control other PROFIBUS stations as a master, selecting this board merely because it supports PROFIBUS would be incorrect.

What Does the Board Do?

With suitable software integration, data generated or processed by a PC can be exchanged with a PLC through PROFIBUS. A test application, for example, could exchange results, status information and commands through agreed data areas. The board supplies the communication interface; the PC application and controller project define what that data means.

A PC station on the fieldbus can perform a different function from the ET 200 distributed I/O stations within the same installation. Our Siemens ET 200 overview and industrial communication guide provide background on these different roles.

Technical Specifications

IM 182-1 uses the SPC 3 ASIC. Its nominal supply is 5 V DC, typical consumption is 250 mA, operating temperature is 0–60 °C, and board dimensions are 168 × 105 mm. Application processing uses the PC/PG processor. PROFIBUS connects through a 9-pin Sub-D connector, while the SPC 3 provides 1.5 KB of internal RAM for the host interface.

Assess the computer's power supply together with the ISA backplane. The specified board supply is 5 V DC; a cabinet's 24 V DC supply must not be applied directly. The 12 Mbit/s figure is the interface's maximum transmission rate. Actual application update time also depends on the network configuration, master cycle and PC software behaviour.

ISA Slot and Host Compatibility

The board requires a compatible computer or industrial PC backplane with an ISA bus. It does not plug directly into PCI or PCI Express slots. When replacing the host computer, processor performance and enclosure dimensions are therefore insufficient selection criteria. Check the expansion bus, available hardware resources and the application's access method together.

Onboard DIP switches configure the PC-side I/O address range and interrupt line. These host resource settings must not be confused with the PROFIBUS station address. Recording the original switch positions and software settings helps when investigating resource conflicts or incorrect hardware access after a replacement.

Drivers, Firmware and Application Integration

Siemens documentation describes a Windows NT driver and firmware running on the host processor. Software integration is required between the board and the application. Successful operation in an older installation does not establish compatibility with another operating system; verify the driver package, application version and hardware access requirements before changing the host.

Catalogued software items include 6ES7 195-2BA00-0XA0 DP firmware, 6ES7 195-2BA01-0XA0 DPV1 firmware and 6ES7 195-2BA02-0XA0 DPV1 firmware upgrade. The specified 4–24 KB describes the firmware scope, including the test program. It should not be interpreted as onboard PLC user-program memory.

Installing the board alone does not complete a SCADA or custom PC integration. The application needs a suitable communication driver and correctly defined data areas. For a value displayed on an HMI to be meaningful, the PC data layout and PLC variable mapping must agree.

PROFIBUS Wiring and Data Configuration

The PROFIBUS side uses an electrically isolated RS-485 interface. A nine-pin connector does not make it electrically interchangeable with a conventional PC serial port. Consider the differences between RS-232, RS-422 and RS-485, and identify a communication port by its electrical specification and pin assignment.

During commissioning, compare the master's station definition, the application's GSD information, input/output data lengths and PC data layout. Communication can be established while values remain incorrect because of byte order, signed/unsigned interpretation or scaling. Following a known test value at both ends helps verify data interpretation as well as the connection itself.

Investigating Communication Faults

Divide fault-finding into the PC, the network and the application. First establish whether the driver can access the board with the configured hardware resources. Then examine master diagnostics, station addressing, bus connectors and segment termination. Finally, check whether the PC application is producing fresh data and whether the master is accessing the intended data area.

If interruptions coincide with motors or other loads switching, inspect cable routing, shield connections and grounding. Faults occurring alongside AC drive operation or contactor switching deserve measurement-based investigation. That timing is a useful clue, but it does not by itself identify a defective board.

Editor's Advice

A spare board is only part of a practical recovery plan. Keep a restorable backup of the working computer, its driver package and application settings. Before removing the board, photograph its complete order number, hardware revision and DIP switches. If the host computer will also change, verify ISA availability and software compatibility before purchasing hardware. A serviceable replacement board does not guarantee that the existing application will run unchanged on another PC.

Technical Documentation and PDF Resources

Our Siemens ET 200 PDF manuals page provides a starting point for system documentation. For IM 182-1, use the board documentation together with the SPC 3 software interface information and the relevant driver/firmware instructions. A general ET 200 installation manual does not, on its own, cover this PC board's resource settings and software integration.

Related Topics

See our PROFIBUS frequently asked questions for further network background. If a system upgrade involves Ethernet or PROFINET, review the communication role and application data model as part of that change. Replacing IM 182-1 with another interface requires more than changing a connector.

Siemens > SIMATIC S7 > Siemens ET 200 > Communication Interfaces