6ES7 133-1BL00-0XB0
Siemens 6ES7 133-1BL00-0XB0 – ET 200L 16 DI / 16 DO
The 6ES7 133-1BL00-0XB0 is an ET 200L electronics block in the Siemens ET 200 family. It combines 16 digital inputs and 16 digital outputs, exchanging field signals with the main PLC through its integrated PROFIBUS DP interface. It is a remote I/O device rather than a standalone CPU running the machine program.
Inputs, outputs and applications
The digital inputs accept 24 V DC signals from switches and suitable proximity sensors. The specified input delay is 2–4.5 ms for both transitions. Check this delay when monitoring short pulses; applications requiring high-speed counting should be assessed against the capabilities of suitable counter modules.
The digital outputs are rated 0.5 A per channel for 24 V DC loads. Suitable loads include solenoids, DC contactors and indicator lights. These are not volt-free relay contacts. Consider inrush current and switching frequency as well as the steady operating current of each load.
Aggregate output current and temperature
The manual specifies aggregate current per output byte, meaning eight outputs. With horizontal mounting, the limit is 4 A up to 30 °C, 3 A up to 40 °C and 2 A up to 60 °C. For other mounting positions, the limit is 2 A per byte up to 40 °C. All 16 outputs therefore cannot be assumed to deliver 0.5 A simultaneously under every installation condition.
Include the connected field loads when planning the power supply and power distribution. Front markings identify 4L+/4M for electronics power, 1L+/1M for output load power and 2L+/2M for sensor power. Check terminal bridges and common return connections against the TB 32L wiring diagram.
TB 32L terminal block
This order number identifies the electronics block. The supporting TB 32L terminal block is a separate component: 6ES7 193-1CL00-0XA0 has screw terminals, while 6ES7 193-1CL10-0XA0 has spring terminals. Permanent field wiring remains on the terminal block. Establish whether the replacement requirement includes the base before selecting parts.
The 1BL00 version cannot be expanded with Smart Connect. Expansion capabilities of ET 200L-SC products should not be assumed for this model. When reviewing the ET 200 family, connection modules and additional modules, use the complete order number to establish compatibility.
PROFIBUS and station addressing
The maximum PROFIBUS DP rate is 1.5 Mbit/s. Two rotary switches marked x10 and x1 select an address from 1 to 99. An address change takes effect when the supply is switched on again. Match the hardware setting to the project and avoid duplicate station addresses.
Use the correct ET 200L device definition and appropriate GSD in the engineering project. Although the wider range of ET 200 communication interfaces includes other protocols, this model has no PROFINET interface. Moving to an Ethernet-based system requires an engineering conversion beyond replacing the bus cable.
Diagnostics and maintenance
The green ON LED monitors electronics power and the red BF LED indicates a bus fault. Individual channels also have green status LEDs. Start fault checks with power, addressing, bus connections and termination. Compare alarms shown on an HMI or SCADA system with the PLC's station diagnostics. Before replacing the block, place the machine in a safe state and isolate the relevant supplies.
Editor's Note: “ET 200 with 16 inputs and 16 outputs” is not a sufficient spare-part specification. Check the full 6ES7 133-1BL00-0XB0 order number, TB 32L base and terminal type together. If a load remains off while ON is lit, check the output group's supply as well as electronics power. Allow for the reduced aggregate output current at higher cabinet temperatures.
Manuals and technical references
For wiring and configuration documents, visit Siemens ET 200 manuals and PDF documents. Technical reference: Siemens ET 200L, ET 200L-SC and ET 200L-SC IM-SC Distributed I/O Device, Edition 04, EWA 4NEB 780 6009-02c; section 2.6 covers addressing, section 7.2 covers TB 32L and section 8.5 contains the data for this exact model.
Navigation: Siemens automation · SIMATIC S7 · Siemens ET 200 · OtomasyonAVM home