6ES7 154-8AB00-0AB0
Siemens 6ES7 154-8AB00-0AB0 – ET 200pro IM 154-8 PN/DP CPU
Siemens 6ES7 154-8AB00-0AB0 is the IM 154-8 PN/DP CPU for the ET 200pro distributed automation system within the SIMATIC ET 200 family. It executes a local user program, allowing a machine section to handle its own control sequence. A conveyor station, for example, can process local signals and operating steps while exchanging coordination data with the wider production system.
Local control within an ET 200pro station
This model brings PLC functionality to the field station. When selecting digital input modules, digital output modules and other station components, check their specific ET 200pro compatibility. Sharing the ET 200 family name does not establish mechanical or electrical interchangeability.
Engineers familiar with S7-300 projects will recognise the programming and hardware configuration approach, while mounting and field connections follow the ET 200pro system design. This order number identifies a standard CPU and should not be confused with an IM 154-8F safety CPU.
Memory and SIMATIC Micro Memory Card
The CPU provides 256 KB of work memory and requires a SIMATIC Micro Memory Card for operation. Supported load memory capacity is up to 8 MB. Card capacity and work memory serve different purposes: installing a larger card does not increase the CPU’s fixed 256 KB work memory. A standard SD card is not a substitute for the specified SIMATIC card.
For an existing machine, review the card contents alongside the project backup and the installed CPU’s hardware details. Card capacity alone does not establish that the correct program and hardware configuration will be available after replacement.
PROFINET and PROFIBUS communication
The integrated PROFINET interface supports IO Controller operation. Its three switched ports belong to one PROFINET interface: two M12 ports on the connection module and one RJ45 service/programming port on the CPU. These are not three independent controller interfaces.
The combined MPI/PROFIBUS DP interface can operate as a DP master or DP slave according to the project configuration. This provides a basis for integrating existing PROFIBUS equipment alongside Ethernet-based field communication. Network roles, station addresses and exchanged data must be defined in the STEP 7 project.
PROFINET operates at 100 Mbit/s, while the MPI/DP interface supports rates up to 12 Mbit/s. Published limits include up to 128 PROFINET IO Devices and 124 DP slaves in DP master operation. These are planning limits; the practical network size also depends on communication load and required response times.
Connection module and protection rating
The associated connection module is CM IM PN DP M12, 7/8″ – 6ES7 194-4AN00-0AA0. Check the connection module together with the CPU order number when preparing a replacement. The presence of the CPU itself does not establish that a connection module, memory card or other accessories are included in a particular supply.
The IP65/67 protection rating depends on suitable connectors and correctly sealed unused ports. After using the RJ45 service connection, its protective cap must be restored correctly. Connector condition, seals and caps therefore deserve attention when inspecting a unit intended for field installation.
Power supply and station planning
Rated supply voltage is 24 V DC, with an operating range of 20.4–28.8 V DC. Typical CPU current consumption is 350 mA and typical power loss is 8.5 W. These figures do not represent the complete station’s power requirement. Include connected modules, sensors and output loads when sizing the power supply.
The ET 200pro supply arrangement separates electronic/sensor power 1L+ from load power 2L+. Account for this separation when selecting DIN rail power supplies and planning distribution. Removing the CPU’s 1L+ supply also disables its integrated Ethernet switch, which can interrupt communication to downstream devices in a line topology.
Engineering software and replacement checks
Siemens lists STEP 7 V5.4 SP1 with HSP 116 or STEP 7 V5.4 SP2 among the engineering requirements for this order number. Match the configured CPU version, installed firmware and hardware catalogue before commissioning. The 6ES7 154-8AB00-0AB0 and similarly named AB01 variant should not be treated as interchangeable without checking their version and functional requirements.
Before replacement, record the CPU label, connection module, memory card and available project backup. If the machine includes an HMI panel or SCADA system, review the associated addresses and data areas. For communication faults, examine diagnostic records, power supplies and network configuration together before concluding that the CPU requires replacement.
Manuals and related topics
For installation, connections and commissioning, consult the IM 154-8 CPU and ET 200pro documentation through our Siemens ET 200 manuals and PDF documentation page. Check that the selected document covers the AB00 order number.
Related topics: Explore the Siemens ET 200 system for an overview of the product family, or visit our industrial communication and PROFIBUS FAQ pages for network background.
Editor’s note: Successful selection depends on matching the CPU, connection module and existing project. Providing a clear label photograph, hardware version and required accessory list helps clarify what is needed when reviewing a unit or requesting a quotation.
Navigation: Siemens products | Siemens S7 PLC | SIMATIC S7 | ET 200 products