6ES7 131-4BD00-0AB0
Siemens 6ES7 131-4BD00-0AB0 – ET 200S 4DI DC24V High Feature Digital Input Module
Siemens 6ES7 131-4BD00-0AB0 is a four-channel, 24 V DC High Feature digital input module for SIMATIC ET 200S stations. It transfers switch and proximity sensor states to the control system. Within the Siemens ET200 family, it belongs to the ET 200S system and offers configurable input delay and sensor supply diagnostics within the digital input module range.
Siemens specifies this order number as a packing unit containing five modules. Each individual electronic module has four input channels. State the required number of modules when requesting a replacement; packaging quantity and channel count are separate details.
High Feature functions
This model allows the input delay to be configured in the project and sensor supply short-circuit diagnostics to be enabled. These functions help align the signal behaviour required by the PLC application with conditions in the field. Recording the existing parameters before replacement helps reproduce the installed module's behaviour.
Pay attention to the complete order number during selection. 6ES7 131-4BD00-0AB0 is the High Feature version. When comparing similar Standard modules, review diagnostic and parameter functions alongside the number of inputs.
24 V DC inputs and field devices
The nominal input voltage is 24 V DC. Siemens specifies −30 to +5 V for signal “0” and +11 to +30 V for signal “1”. The region between those limits should not be used to establish a reliable logic state.
The module accepts suitably rated proximity sensors, limit switches, pushbuttons and relay contacts. Two-wire sensor connection is supported, with a maximum permitted off-state current of 1.5 mA. For electronic sensors, check the output type and off-state current together.
Configurable input delay
The input delay can be set to 0.1 ms, 0.5 ms, 3 ms or 15 ms. The manufacturer's manual specifies a default of 3 ms. This setting applies to the whole module and affects both 0→1 and 1→0 transitions.
A brief position signal and an operating-state signal from a mechanical contact may require different filtering. Consider the actual signal duration, contact bounce and electrical interference when choosing the delay. If a setting is changed to resolve a problem on one input, check the behaviour of the other three inputs as well.
Hardware interrupt and isochronous operation support are provided. Using these functions also requires a suitable station interface and project configuration. Assess the input delay, data transfer and CPU program together when reviewing application timing.
Sensor supply and short-circuit diagnostics
The sensor supply output provides 500 mA total per module and has electronic short-circuit protection. The combined consumption of connected sensors must remain within this capacity. Review the sensor supply wiring against the connection arrangement of the selected terminal base.
Diagnostics can be enabled for a sensor supply short circuit to M. The manual lists this diagnostic setting as disabled by default. Enabling it in the project helps maintenance personnel distinguish a supply-related fault; interpret the message with reference to the sensor supply circuit.
Terminal module and mounting compatibility
The electronic module plugs into a suitable TM-E terminal base. Siemens connection examples include TM-E15S24-01 / 6ES7 193-4CB20-0AA0 and TM-E15S26-A1 / 6ES7 193-4CA40-0AA0. Compare complete order numbers when matching ET200 terminal blocks and reviewing the station's connection modules.
The terminal version affects the distribution of sensor supply and auxiliary potentials. Understanding the base's connection arrangement is as important as retaining the original wire positions. Recording the labels of both the electronic module and terminal base before replacement helps ensure a correct match.
Addressing, communication and indicators
The module occupies 1 byte without address packing or 4 bits with supported address packing. Check packing availability against the existing project and station configuration. Verify the correspondence between each physical channel and its program input address after replacement.
The station's industrial communication connection depends on its interface module. For ET 200S stations operating over PROFIBUS or PROFINET, review the interface details alongside the input module's order number.
The front panel has green channel status indicators and a red SF group-error indicator. During maintenance, compare the field signal, LED state and program input bit for the same physical point. A clear sensor supply fault message on the HMI panel or SCADA screen is more informative than a general station fault message.
Dimensions and electrical design
The module body measures 15 × 81 × 52 mm and weighs approximately 35 g. Typical power loss is 0.7 W. The channels are not galvanically isolated from each other; isolation is provided between the inputs and backplane bus. Cabinet planning should also allow for the terminal base and access to the wiring.
Technical documentation and related topics
For connection and parameter details, consult the relevant ET 200S documents through the Siemens ET200 PDF manuals page. Further background is available in the Siemens ET200 overview, the PROFIBUS frequently asked questions and the PLC systems and modules section.
Editor's note: Record the input delay and sensor supply diagnostic settings before replacing this model. Reading the same four signals does not establish identical machine behaviour when two modules use different parameters. Compare the order number, terminal base and existing settings together.
More Siemens products: Siemens products | Siemens S7 PLC | SIMATIC S7 | ET200 products