6ES7 141-1BF01-0AB0

Siemens Main Menu  |  SIMATIC S7  |  Siemens ET 200  |  PDF Manuals

6ES7 141-1BF01-0AB0 - Siemens SIMATIC ET 200X BM 141 ECOFAST 8 DI Basic Module

Series: SIMATIC ET 200X
Product type: ECOFAST basic module with PROFIBUS-DP and 8 digital inputs
Input voltage: 24 V DC
Field connection: 8 × M12 input sockets
Order number: 6ES7141-1BF01-0AB0

6ES7 141-1BF01-0AB0 is a BM 141 ECOFAST basic module in the Siemens ET 200 distributed I/O family. It communicates over RS485-based PROFIBUS-DP through copper conductors and provides eight 24 V DC digital inputs for switches and proximity sensors.

The station’s basic module, not an expansion card

This product is more than a digital-input card. The PROFIBUS address, RS485 interface, power entry, RUN and SF indicators and ET 200X backplane connection are integrated in the same housing. It acts as the main device that transfers expansion-module data to the SIMATIC S7 automation system.

Do not treat 6ES7141-1BF01-0XB0 as the same product. This 0AB0 version uses the ECOFAST connection architecture. Power and PROFIBUS signals are carried through combined six-pin X01 and X02 connections. Housing, cabling and power arrangement differ, so substitution based only on “BM 141, 8 DI” is unsafe. Assess the complete order number within the ET 200 system architecture.

Key technical specifications

Digital inputs: 8.
Rated input voltage: 24 V DC.
Signal 1: 13 to 30 V; typical input current 7 mA.
Signal 0: -3 to +5 V.
Input characteristic: IEC 61131 Type 1.
Input delay: 1.2 to 4.8 ms for both 0→1 and 1→0.
Two-wire sensor: supported; permissible quiescent current 1.5 mA maximum.
Simultaneous inputs: all 8 up to 55 °C.
PROFIBUS-DP speed: 9.6 kbit/s to 12 Mbit/s.
FREEZE and SYNC: supported.
Manufacturer identification: 80D2H.
Sensor cable: 30 m maximum, unshielded.
Current consumption: 180 mA maximum from 1L+.
Power loss: typically 3.5 W.
Dimensions: 175 × 180 × 110 mm.
Weight: approximately 650 g.

When comparing ET 200 digital input modules, check whether the product is a basic or expansion module, its ECOFAST connection, PROFIBUS identity and diagnostic capability—not only its input count.

Pin assignment of the eight M12 sockets

This model has eight separate M12 input sockets, X1 through X8. Each socket carries one digital-input channel: X1 is channel 0, X2 is channel 1 and the sequence continues through channel 7 on X8. Pin 1 is sensor supply 1L+, pin 3 is sensor-supply ground, pin 4 is the input signal and pin 5 is PE. Pin 2 is not assigned.

This differs from the 6ES7141-1BF31-0XA0 expansion module, which carries eight inputs through four dual-assigned sockets. There is no second input on pin 2 here. When selecting ET 200 M12 connection modules and connectors, remember that every socket on this basic module represents one channel.

ECOFAST X01 and X02 connections

X01 is the supply and PROFIBUS entry; X02 loops the same circuits through. Both connections use pin 1 = L+ NS, pin 2 = M NS, pin 3 = M S, pin 4 = L+ S, pin 5 = PROFIBUS signal A and pin 6 = PROFIBUS signal B. NS is the non-switched electronics and sensor supply; S is the switched load circuit.

This combined arrangement carries power and PROFIBUS through one ECOFAST cable system. A conventional PROFIBUS M12 cable or ordinary power lead is not an equivalent substitute. When designing the ET 200 PROFIBUS connection architecture, verify the X01/X02 direction, A-B data pair and NS-S power separation together.

Power current and protection

The NS and S supply circuits are rated for 24 V DC. Siemens specifies a maximum current of 10 A up to 40 °C and 8 A up to 55 °C through the connections. These load circuits have no internal reverse-polarity or short-circuit protection. Protect the station externally with suitable fuses and conductor sizes.

Each of the eight sensor-supply outputs has electronic short-circuit protection. The per-output limit is 1 A up to 40 °C or 0.8 A up to 55 °C; the overall current limit of the complete ET 200X station must also be respected. Calculate the ET 200 power supply system and ET 200 field power distribution together.

Difference from the ECOFAST DIAG version

6ES7141-1BF01-0AB0 provides configurable station diagnostics and indicators for group fault, RUN state and the NS and S supply voltages. A diagnostic interrupt may be used for missing load voltage. Its digital-input section, however, does not provide the channel features of the 6ES7141-1BF40-0AB0 ECOFAST DIAG version.

Do not assume the channel wire-break and short-circuit-to-M diagnostics, rising or falling-edge hardware interrupts or parameterizable input delays available on the 1BF40-0AB0 DIAG version. A green channel LED confirms electrical input state only; it does not prove correct sensor alignment or process operation.

Expansion-module compatibility

Siemens ET 200X product information states that the older 6ES7141-1BF30-0XA0 and 6ES7141-1BD30-0XA0 digital expansions and the 6ES7148-1DA00-0XA0 pneumatic module should not be used with ECOFAST basic modules. A sensor-line short circuit can otherwise cause a failure of the station’s 24 V supply.

Adapted alternatives include 6ES7141-1BF31-0XA0, 6ES7141-1BD31-0XA0 and the revised diagnostic versions. When extending a used installation, verify the complete order number and product revision rather than checking only whether the module fits mechanically.

Six field checks for commissioning

1. Verify the ECOFAST cable set. X01 is the power and PROFIBUS entry; X02 is loop-through. A standard M12 PROFIBUS cable cannot replace the combined connection.

2. Keep PROFIBUS A and B correct. Pin 5 is signal A and pin 6 is signal B. If communication fails, first check the pinout, station address and bus termination.

3. Preserve NS and S separation. Pins 1-2 are the non-switched NS circuit, while pins 3-4 are the switched S circuit. Incorrect bridging can make supply diagnostics meaningless.

4. Do not omit external fusing. The power inputs have no internal reverse-polarity or short-circuit protection. Select the fuse from conductor size, ambient temperature and total downstream load.

5. Seal unused M12 sockets. IP65, IP66 or IP67 protection requires the correct caps and undamaged seals. Prepare the ET 200 field connection arrangement for water, oil, metal swarf and vibration.

6. Separate standard inputs from safety signals. This product is not a PROFIsafe F-DI. Emergency-stop, guard-door and light-curtain signals require suitable ET 200 safety modules.

Used-unit inspection

Confirm the full 6ES7141-1BF01-0AB0 code and product revision. Inspect the X01/X02 ECOFAST pins and locking parts, all eight M12 sockets, PROFIBUS address cover, channel LEDs, RUN-SF indicators and housing seals separately. A broken ECOFAST lock or missing seal is a functional defect rather than a cosmetic issue.

Missing protective caps and mounting parts may be completed from ET 200 accessories and supplementary modules. Photographs showing the label, ECOFAST ports and M12 sockets can be sent through the Otomasyon AVM Siemens contact page.

Editor’s note

The most dangerous mistake is treating the 0AB0 ECOFAST model as identical to the conventionally connected 0XB0 version. The ECOFAST connector carries power and PROFIBUS together and keeps NS and S supplies separate. The older 1BF30-0XA0 and 1BD30-0XA0 expansions are also unsuitable for this basic module. On a used unit, ask whether the ECOFAST cable set is included; missing cables can increase the actual installation cost substantially.

PDF manuals and documentation

Consult ET 200X Distributed I/O Device, Edition 02/2003, EWA 4NEB 780601602-06 on the Siemens ET 200 PDF manuals page. Section 7.2 covers the exact model pin assignment, circuit, parameters and technical data; section C.11 covers the ECOFAST X01-X02 connections.