6ES7 138-4FA02-0AB0

Siemens main menu › SIMATIC S7 › SIMATIC ET 200

Siemens 6ES7 138-4FA02-0AB0 — ET 200S 4/8 F-DI PROFIsafe Fail-Safe Input Module

6ES7 138-4FA02-0AB0 is a 4/8 F-DI DC 24 V PROFIsafe fail-safe digital input module for the ET 200S series within the Siemens ET 200 distributed I/O family. With suitable sensors and an engineered safety application, it evaluates signals from devices such as emergency-stop switches or protective doors. Its selection requirements differ from those of standard ET 200 digital input modules.

Order number: 6ES7138-4FA02-0AB0
Input arrangement: 8 single-channel or 4 dual-channel evaluations
Rated supply: 24 V DC
Supply range: 20.4–28.8 V DC
Dimensions (W × H × D): 30 × 81 × 52 mm
Approximate weight: 78 g

What does 4/8 F-DI mean?

The eight physical inputs provide eight signals in single-channel evaluation or four signal pairs in dual-channel evaluation. Siemens specifies maximum levels of SIL 2 / Category 3 for single-channel use and SIL 3 / Category 4 for dual-channel use. For ET 200 fail-safe modules, these levels depend on the sensors, wiring and configuration.

The dual-channel pairs are DI0–DI4, DI1–DI5, DI2–DI6 and DI3–DI7. Two adjacent inputs must not be paired arbitrarily. The module does not provide eight independent SIL 3 signals.

Five selection checks before ordering

1. Controller and communication: Check the F-CPU, F-address and software configuration for PROFIsafe safety communication. The datasheet specifies PROFINET operation with IM151-3 HF; still verify the full order number and revision of the installed ET 200 communication interface.

2. Sensors and supply: Identify the sensor contact arrangement and whether the supply is internal or external. The module provides Vs1 and Vs2 sensor supplies, each rated up to 300 mA. Include sensor consumption when checking the ET 200 power supply modules and ET 200 power distribution arrangement.

3. Evaluation and test settings: Single- or dual-channel evaluation, equivalent or non-equivalent sensor operation, discrepancy time and short-circuit testing must match the project. Do not change test settings simply to clear a diagnostic message. First compare the sensor wiring with the applicable application diagram.

4. Terminal base: The manual lists TM-E30S44-01, TM-E30C44-01, TM-E30S46-A1 and TM-E30C46-A1. Check the termination method and AUX1 arrangement when selecting ET 200 terminal blocks. Do not match ET 200 connection modules solely by their 30 mm width.

5. Revision and scope of supply: Distinguish 4FA02 from the similar 4FA03, 4FA04 and 4FA05 order codes. If an alternative is offered, check the manufacturer's replacement conditions and the project configuration. Confirm whether the terminal base and required ET 200 additional modules and accessories are included.

Separate input diagnostics from output control

This component is an F-DI input module. The ET 200 digital output modules controlling loads serve a separate role. A machine that will not start does not by itself establish an input-module failure. Examine sensor signals, supply conditions and safety diagnostics together.

Siemens application document 22304119 lists 4FA02 among the modules supporting channel-level passivation with the required software. Do not assume that every channel fault must affect the entire module in the same way. Check the configured fault response and reintegration conditions.

Editor's note

Selecting this module requires attention to sensor wiring and input evaluation as well as the order number. Compare the label, terminal base and existing project together. An illuminated input LED does not validate the safety function; relevant functions must be checked by qualified personnel after replacement.

Manuals and PDF documentation

On our Siemens ET 200 PDF and user manuals page, use ET 200S Fail-Safe Modules, 07/2005, A5E00103686-04, section 7.5 as the reference for this version. This edition explicitly covers 6ES7138-4FA02-0AB0. Siemens document 22304119 provides supplementary guidance on passivation and reintegration.

Related topics and Siemens navigation

Product family: Siemens main menu  |  SIMATIC S7  |  ET 200 family

Safety and inputs: Fail-safe modules  |  PROFIsafe  |  Digital input modules

Connections and documentation: Terminal blocks  |  Power supply modules  |  ET 200 PDF manuals