6ES7 138-4DF00-0AB0
Siemens Main Menu | SIMATIC S7 | Siemens ET 200 | PDF Manuals
6ES7 138-4DF00-0AB0 — Siemens ET 200S 1SI Serial Interface Module
6ES7 138-4DF00-0AB0 is a 1SI electronic module that adds serial communication to ET 200S stations in the Siemens ET 200 distributed I/O family. It can exchange data between a SIMATIC S7 control system and a barcode reader, computer or suitable serial device, provided the electrical interface and message format match.
Function and protocol selection
Its physical interface options are RS232C, RS422 and RS485, with ASCII and 3964(R) protocol drivers. It has one channel: these interface names do not indicate three independent serial ports. The ET 200 PROFIBUS and PROFINET interfaces connect the station to the PLC network, while the 1SI handles the serial device connection.
RS485 alone does not establish Modbus support. Matching terminal names is insufficient when a device requires Modbus or USS. Establish how the required protocol will be provided by the module driver or application software.
Key technical details
Order number: 6ES7138-4DF00-0AB0.
Module: ET 200S 1SI, one serial channel.
Rated supply: 24 V DC.
Dimensions: 15 × 81 × 52 mm (width × height × depth).
Indicators: Green TxD and RxD, red SF.
Baud-rate reference: The Siemens data sheet dated 18 August 2019 specifies a maximum of 19.2 kbit/s; verify the intended rate against the product version and project.
Five selection and commissioning checks
1. Read the complete code and product version. When reviewing the ET 200 system architecture, record the station interface code as well. For example, the manual for IM151-3 PN HIGH FEATURE / 6ES7151-3BA23-0AB0 lists 4DF00 modules up to product version 4 as unsupported. Do not extend this restriction into a universal compatibility rule for every IM151 model.
2. Verify the terminal base. Select ET 200 terminal blocks against the wiring diagram for the complete module code. When reviewing ET 200 connection modules and wiring arrangements, check the signal terminals, shielding and selected RS interface together.
3. Inspect the supply group. Match the ET 200 power supply modules to the electronic module’s requirements. Record the existing ET 200 power distribution arrangement and measure supply stability as part of communication troubleshooting.
4. Compare communication settings. Both ends must agree on baud rate, data bits, parity, stop bits and message termination. For ASCII, inspect the actual message sent by the partner device: readable data on a screen does not prove that the PLC program separates messages correctly.
5. Review software and hardware together. Check that the send/receive blocks suit the module version, then verify their addresses and status codes. Identify any required terminal base, shielding component or other ET 200 additional modules and accessories separately against the scope of supply.
Editor’s note
A common selection mistake is treating the serial interface type as the protocol. Start with the partner device’s communication documentation, then compare the module’s complete code and version. The documents differ on baud rate: the Siemens NS K 2002 catalogue lists 38.4 kbit/s, while the 2019 data sheet lists 19.2 kbit/s. Do not assume the higher rate is supported without resolving this discrepancy for the installed unit. For troubleshooting, record the TxD/RxD behaviour, PLC block status code and a sample message instead of reporting only “no data”. Share these details through the Otomasyon AVM Siemens contact page when requesting a product assessment.
PDF manuals and documentation
On the Siemens ET 200 PDF manuals page, review the 1SI serial communication documents alongside the manual for the installed IM151 interface. A5E00124881-05 Serial Interface Modules explains operation and diagnostics; its product scope includes later order numbers, so do not automatically transfer baud-rate, block or terminal information to the 4DF00. The IM151 compatibility restriction above is documented in A5E01584258-04, section 1.1, printed page 12.
Related topics and Siemens navigation
Communication interfaces | Terminal blocks | Connection modules
Power supply modules | Additional modules and accessories | ET 200 system architecture
Siemens Main Menu | SIMATIC S7 | Siemens ET 200 | PDF Manuals