6ES7 132-1BL00-0XB0
Siemens Main Menu | SIMATIC S7 | Siemens ET 200 | PDF Manuals
6ES7 132-1BL00-0XB0 — Siemens ET 200L 32 DO 24 V DC/0.5 A Digital Output Block
6ES7 132-1BL00-0XB0 is a 32-channel digital output electronics block for the ET 200L series in the Siemens ET 200 distributed I/O family. It connects 24 V DC solenoid valves, DC contactors and indicator lamps to a SIMATIC S7 control system through PROFIBUS-DP.
Why the ET 200L architecture matters
This product is not an ET 200S plug-in electronic module. Its PROFIBUS-DP interface, address switches, output electronics and status LEDs are integrated in one block. A TB 32L terminal block is required. When comparing ET 200 digital output modules, the system family and mechanical base must therefore match; 32 DO and 0.5 A ratings alone are not sufficient.
The Siemens manual describes the 32 outputs as two groups of 16 outputs. Its current-derating table is specified per output byte, or eight-channel section. These two groupings must not be confused.
Key technical details
Order number: 6ES7132-1BL00-0XB0.
Product family: SIMATIC DP ET 200L.
Product type: 32 DO electronics block.
Output voltage: 24 V DC.
Current per channel: 0.5 A maximum.
Output groups: 2 × 16 channels.
Required terminal block: TB 32L.
Communication: PROFIBUS-DP, up to 1.5 Mbit/s.
SYNC capability: yes.
Dimensions: 145 × 60 × 60.5 mm.
Weight: approximately 150 g.
Degree of protection: IP20.
Typical power loss: 7 W.
The outputs are short-circuit protected; the current Siemens data sheet specifies a typical response threshold of 0.7 A. There is one green status LED per channel, a green ON LED for electronics supply and a red BF LED for PROFIBUS faults. The block supports diagnostics but provides no hardware interrupts. Communication and diagnostics must be assessed together with the ET 200 PROFIBUS interface architecture.
Six selection and commissioning checks
1. Confirm the ET 200L and TB 32L combination. This electronics block does not fit ET 200S terminal modules. When reviewing ET 200 terminal connection components, verify the TB 32L code, terminal style and whether the terminal block is included with a used unit.
2. Do not directly calculate “32 × 0.5 A = 16 A”. Total output current is limited per eight-channel output byte according to temperature and mounting position. With horizontal mounting, the limit per byte is 4 A up to 30 °C, 3 A up to 40 °C and 2 A up to 60 °C. For other mounting positions, the limit is 2 A per byte up to 40 °C.
3. Separate electronics and load supplies. Electronics power is connected through 4L+/5L+, while output load supplies use 1L+, 2L+ and 3L+. When designing the ET 200 power supply architecture and ET 200 power distribution arrangement, calculate protection, conductor size, common M connections and voltage drop separately.
4. Compare PROFIBUS settings with the existing project. The address is selected using the ×10 and ×1 switches on the block. Supported rates range from 9.6 kbit/s to 1.5 Mbit/s, and SYNC is supported. Verify the hardware catalogue, GSD file, DP address and ET 200 system architecture before replacing the block.
5. Check load type and switching rate. Maximum switching rate is 100 Hz for resistive loads, 0.5 Hz for inductive loads and 8 Hz for lamp loads. Lamp load is limited to 5 W per channel. Two outputs may be paralleled only within the same group for redundant control; paralleling for current uprating is not permitted. Use an interposing relay or contactor in the ET 200 connection arrangement for heavier loads.
6. Support diagnostics with real load feedback. The BF LED identifies a PROFIBUS fault, the ON LED confirms electronics supply and the green channel LEDs show output commands; none proves that the actuator has moved. Use a limit switch or auxiliary-contact return through ET 200 digital inputs for critical valves and contactors.
Installation and wiring details that are easily missed
The standard arrangement is two-wire, while optional three- and four-wire connections are available with TB 32L. Maximum cable length is 600 m unshielded or 1000 m shielded, but these limits do not replace voltage-drop calculations at a 0.5 A load. A minimum 20 ms power-failure withstand time is stated for the electronics supply; machine-safe stopping must not depend on that interval.
Editor’s note
The expensive mistake with this product is buying the bare electronics block and assuming that it will fit an existing ET 200S base. 6ES7132-1BL00-0XB0 belongs exclusively to the ET 200L architecture and requires a TB 32L base. For a used unit, ask whether the TB 32L, PROFIBUS connector and labelling strip are included. Share the block label, terminal-block photo, BF/ON LED state and current DP address through the Otomasyon AVM Siemens contact page for a more reliable assessment.
PDF manuals and documentation
Consult section 8.4 of ET 200L Distributed I/O Device — EWA-4NEB 780600902-05 on the Siemens ET 200 PDF manuals page. It documents the output groups, supply arrangement, current derating and load limits for 6ES7132-1BL00-0XB0. Compare the terminal block and PROFIBUS connection against the same system manual when selecting ET 200 accessories and supplementary connection parts.
Related topics and Siemens navigation
Digital output modules | Terminal connections | Power supply modules
Power distribution modules | PROFIBUS interfaces | ET 200 system architecture
Siemens Main Menu | SIMATIC S7 | Siemens ET 200 | PDF Manuals