6ES7 132-0BH11-0XB0
Siemens main menu › SIMATIC S7 › SIMATIC ET 200
Siemens 6ES7 132-0BH11-0XB0 — ET 200B 16 DO 24 V DC/2 A Electronics Block
6ES7 132-0BH11-0XB0 is the ET 200B-16DO/2A electronics block in the Siemens ET 200 distributed I/O family. It provides 16 digital outputs at 24 V DC, with a maximum of 2 A per channel. This model in the ET 200 digital output range can operate suitable DC coils and control loads. Load selection must account for both the individual output rating and the total current of each four-channel group.
Order number: 6ES7132-0BH11-0XB0
Series: SIMATIC ET 200B
Outputs: 16 DO, isolated in groups of four
Channel / group limit: 2 A / 4 A maximum
Communication: PROFIBUS-DP
Protection rating: IP20
Electronics block and terminal base together: 235 × 130 × 60 mm
ET 200B construction and application
When reviewing the ET 200 system architecture, distinguish between its different series: this product belongs to ET 200B. The electronics block and the terminal base carrying the field wiring are separate components. Assess ET 200 communication options against the existing PROFIBUS-DP network. A 16-output module from another ET 200 series should not be assumed to fit the same installation.
Five checks before selection or replacement
1. Channel and group current: Each output has a 2 A limit, but the combined load of a four-channel group must not exceed 4 A. For example, four loads drawing 1.5 A each would total 6 A and exceed that limit. When planning ET 200 power distribution, calculate the simultaneous load for each group; the overall power supply capacity alone does not establish suitability.
2. Logic and load supplies: The Siemens wiring diagram identifies the load groups as L1+/M1 through L4+/M4 and the logic supply as L5+/M5. When checking ET 200 power supply components, measure each group supply against its own return. If communication is working but some outputs remain inactive, also inspect the group supplies, fuses and terminal connections.
3. Terminal base: The product data sheet lists TB2/DC, TB2-4/DC, TB4/DC and TB4-4/DC. When selecting from the ET 200 terminal block range, compare the complete base reference and wiring arrangement with the installed unit. Inspect ET 200 connection components for loose contacts, corrosion or signs of overheating separately from the electronics block.
4. PROFIBUS and hardware definition: The device definition, station address and output addresses in the Siemens S7 hardware project must match the installed hardware. Record existing address settings and wire markings before replacement. For bus faults, inspect termination and connectors so that an addressing error is not carried over to the replacement block.
5. Output protection and load feedback: The outputs have electronic short-circuit protection. A faulty load or cable short still needs to be located and corrected. An illuminated output LED alone does not prove that a contactor has operated or a valve has moved. Where required, monitor actual equipment state using an appropriate sensor or auxiliary contact connected to ET 200 digital input modules.
How 0BH01 differs from 0BH11
6ES7132-0BH01-0XB0 also has 16 outputs, but uses a 12 × 0.5 A + 4 × 2 A arrangement and different terminal base options. Channel count alone is therefore insufficient when selecting 0BH11. When comparing products through the Siemens main menu, check the complete order number, load distribution and terminal base together.
Editor's note
The detail most easily overlooked is the distinction between the 2 A channel limit and the 4 A group limit. Map each load to its output group before selecting a spare. An unsuitable load distribution can keep causing problems even after the correct replacement block is installed.
Manuals and PDF documentation
On our Siemens ET 200 PDF and user manuals page, consult the ET 200B Distributed I/O Station system manual. EWA 4NEB 812 6089-02c, section 7.3.4, pages 7-32–7-37 covers this electronics block. Use the relevant terminal-base section for wiring details and the 6ES7132-0BH11-0XB0 data sheet for product ratings.
Related topics and Siemens navigation
Product family: Siemens main menu | SIMATIC S7 | ET 200 family
Station and field devices: Digital output modules | Terminal blocks | PROFIBUS and PROFINET
Technical resources: About ET 200 | Power supply modules | ET 200 PDF manuals