• Gemo DT721

Gemo DT721 is a compact 72 × 72 mm digital temperature controller with simple two-button adjustment. Depending on the ordered version, it can be used with J or K type thermocouples and provides straightforward ON/OFF temperature control. OtomasyonAVM has been supplying Gemo products since 2013.

Standard supply: 100–240 VAC, 50–60 Hz.
If a 24 VAC/DC supply version is required, this must be specified when ordering.
Sensor input: Fe-Const J type thermocouple or NiCr-Ni K type thermocouple, depending on the ordered version.
Output: Relay output as standard. If an SSR output version is required, specify this when ordering.

The DT721 uses adjustable hysteresis and ON/OFF control rather than PID. It is intended for applications where simple temperature switching is sufficient.

Setting the temperature

The display alternates between SEt and the current SET value. Use the Up and Down arrow keys to enter the required temperature.

After setting the new value, leave the keys untouched for approximately two seconds. The new SET value is stored automatically.

Hysteresis setting

The display alternates between Hys and the current hysteresis value. Use the Up and Down keys to enter the required setting.

After the adjustment, leave the keys untouched for approximately five seconds. The hysteresis value is then stored automatically.

Hysteresis range: 0–50 °C.

ON/OFF control behaviour

When the measured Process Value PV ≥ SET, the OUT output switches OFF.

When PV falls to or below SET − Hys, the OUT output switches ON again.

The hysteresis setting helps prevent unnecessary relay switching around the SET temperature.

Upper SET limit

The UP.L parameter can be used to limit the highest SET value that the operator is allowed to enter.

The display alternates between UP.L and the current upper-limit value. Adjust the limit with the Up and Down keys, then leave the keys untouched for approximately five seconds to store the new value.

Sensor fault indication

If or appears on the display, check the thermocouple and its wiring. Possible causes include an open sensor circuit, measurement outside the selected range, reversed thermocouple polarity or an input fault.

Sensor protection: If the sensor circuit is open, the measurement is outside the valid range or the input cannot be measured correctly, the OUT output will not energize.

Other compatible temperature sensing products can be found in our temperature sensors section.

Technical specifications

Front dimensions: 72 × 72 mm.
Display: 3-digit, 7-segment display.
Control method: ON/OFF.
Adjustable hysteresis: 0–50 °C.
SET upper limit: Adjustable with the UP.L parameter.

J type measuring range: 0–600 °C.
K type measuring range: 0–999 °C.
J type SET range: 0–600 °C.
K type SET range: 0–999 °C.

Thermocouple compensation: Ambient temperature compensation from 0 to 50 °C.
Input: Fe-Const J type T/C or NiCr-Ni K type T/C, depending on the ordered version.

OUT relay: NO + NC, 250 VAC / 2 A resistive load.
SSR output: Optional.

Supply voltage: 100–240 VAC, 50–60 Hz or optional 24 VAC/DC.
24 V version isolation voltage: Maximum 40 VAC.
Power consumption: < 6 VA.
Protection rating: IP20 according to EN 60529.

Safety: EN 61010-1; pollution degree 1, measurement category I.

Memory: SET, hysteresis and control parameters remain stored when power is removed.

Control panel installation

The DT721 can be used in control panels containing AC drives and other switching equipment. Thermocouple wiring should be kept separate from motor and inverter power cables where possible.

Keeping the low-level thermocouple signal away from power wiring helps reduce electrical interference and unstable temperature readings.

Gemo DT721 User Manual (PDF)

Gemo price list
Gemo contact information
Gemo main page
Industrial control devices

Installation: Thermocouple, supply and output wiring should be carried out by qualified technical personnel.

Before applying power, check the thermocouple type and polarity, supply voltage and relay/SSR output configuration against the product documentation.

Write a review

Note: HTML is not translated!
Bad Good

Gemo DT721

  • 21.00USD

  • Ex Tax: 21.00USD

Related Products

DESA-77R-A Analog Temperature Controller, 220V

DESA-77R-A Analog Temperature Controller, 220V

▪︎ DERELL DESA-77R-A >> 220V Power Supply, Relay Output, 72x72 mm Panel Type Temperature Contr..

128.00USD Ex Tax: 128.00USD

DGS-77R-A Advanced Temperature Controller (220V)

DGS-77R-A Advanced Temperature Controller (220V)

— Next-generation temperature compensation with high precision DGS-77R-A >> 220V pow..

131.00USD Ex Tax: 131.00USD

DGS-77T-A – Advanced Serial Type with SSR Output – 220V

DGS-77T-A – Advanced Serial Type with SSR Output – 220V

— Next-generation temperature compensation with high precision DGS-77T-A >> 220V pow..

136.00USD Ex Tax: 136.00USD

DGS-77R-B Advanced Temperature Controller (24VAC/DC)

DGS-77R-B Advanced Temperature Controller (24VAC/DC)

— Next-generation temperature compensation with high precision DGS-77R-B >> 24VDC/AC..

205.00USD Ex Tax: 205.00USD