Delta DVP14EC00T3

Delta DVP14EC00T3 | PLC with 8 Inputs and 6 Transistor Outputs

The Delta DVP14EC00T3 is a 100–240 V AC PLC main unit in the Delta DVP-EC3 series. It has 8 digital inputs rated at 24 V DC and 6 NPN transistor outputs. It reads sensors and switches DC control loads in small packaging machines, part-counting stations and compact conveyor panels.

X0–X7 inputs and high-speed counting

The onboard inputs are addressed X0–X7. The S/S common sets the input circuit for sinking or sourcing. Check the PNP or NPN signal type against the panel diagram. When replacing an inductive sensor, photoelectric sensor or limit switch, verify the input voltage and common connection.

The 20 kHz input group differs between sheet editions. The 2010 sheet specifies 20 kHz for X0 and X1. The 2014 sheet specifies it for X0–X3. For an incremental encoder, check the sheet applicable to the unit, the assigned input pair and the frequency limit of the selected high-speed counter mode.

Y0–Y5 outputs and pulse control

The Y0–Y5 outputs are NPN open-drain outputs for DC loads. Delta specifies an external 24 V DC auxiliary supply for the output circuit’s UP and ZP terminals. The output table lists a 5–30 V DC operating range and a resistive-load limit of 0.5 A per point. Check the common-terminal current and inductive-load limits in the applicable sheet. Use a suitable flyback diode or suppressor for DC coils and an appropriately rated interposing relay for AC coil control.

The 2010 hardware sheet lists 1 kHz for standard transistor outputs. Delta’s later catalogue specifies two independent pulse outputs up to 10 kHz on Y0 and Y1 with applicable V8.00 or later hardware. For a servo or stepper motor drive, check the CPU version, program instruction and drive pulse-input circuit together.

4K and 8K versions | Programming software

Use WPLSoft for EC3 projects. Earlier EC3 units were documented with 4K steps. Delta’s programming manual specifies 8K steps for firmware V8.60 or later. For this version, select EC3-8K in ISPSoft. Start the serial channel in COMMGR and select the same channel in ISPSoft. See the guides to ladder diagrams and PLC programming when reading the project.

COM1 and programming cable

The sole built-in serial port is 8-pin mini-DIN COM1 / RS-232. Use UC-PRG020-12A for a USB-equipped PC or UC-MS020-01A for a PC with a physical RS-232 port. Install the USB cable driver and select the COM port assigned by Windows. For an HMI connection, check the panel’s Delta PLC driver and serial settings. See Delta PLC cables and the guide to RS-232, RS-422 and RS-485 when choosing the cable.

The onboard I/O count is fixed. Count the inputs and outputs needed when planning the panel. For 0–10 V or 4–20 mA measurements, plan a suitable measurement interface. See the guide to analog and digital inputs when selecting the signal interface.

Editor’s Note

Check the label and terminals. When buying used, ask for photos showing the 00T3 suffix and the UP and ZP output terminals.

Check the shared supply if all outputs fail. If the Y LEDs light and the loads stay off, check UP/ZP supply voltage, polarity and load wiring.

Verify pulses under load. Safely prevent machine motion before measuring Y0 and Y1 at the drive input. Check the CPU version and output instruction together.

Budget the auxiliary 24 V supply. The sheet specifies 200 mA for this model. Include the current drawn by the inputs and plan a separate HMI supply.

Back up the CPU before removing it. Save the program, required retained values and COM1 settings. Read the replacement CPU’s version to verify the 4K or 8K project target.

Internal References | Related Delta Models

The DVP14EC00R3 has the same 8/6 I/O split with relay outputs. The DVP10EC00T3 has 6 inputs, 4 transistor outputs and one serial port. For panels that require built-in COM2 / RS-485, the DVP16EC00T3 has an 8/8 I/O split and the DVP20EC00T3 has a 12/8 split.

Related Topics

Check the home position on moving axes and NO and NC contact logic on field inputs. See grounding and fuses for the panel supply, and safety relays for emergency-stop and guard-door circuits.

OtomasyonAVM PDF and Series Links

Delta DVP PLC files · Delta DVP-EC3 hardware and terminal sheet, 2010 (PDF)

All Delta DVP PLC series · Used Delta models

External References

Delta EC3 hardware sheet, 2014 (manufacturer download page) · Delta DVP-PLC programming manual and EC3-8K version note (EN, PDF) · Delta PLC/HMI cable selection guide, section 1.3 (EN, PDF)