Delta DVP02TUN-S

Delta DVP02TUN-S – 2-Channel PID Temperature Control Module

Delta DVP02TUN-S is a temperature control module with two universal analog inputs and four NPN transistor outputs. It mounts on the right side of a compatible Delta DVP Slim PLC. The two channels have independent measurements and setpoints. Its built-in PID control can regulate two heater jaws on a packaging machine or two zones in a mould.

Sensor inputs and power supply

CH1 and CH2 accept Pt100, JPt100, Pt1000 and other supported RTDs, J and K as well as other thermocouple types in Delta’s table, and standard analog input signals. The voltage ranges are 0–5 V, 0–10 V, 0–50 mV and ±100 mV. The current ranges are 0–20 mA and 4–20 mA. The module requires an external 24 V DC supply (20.4–28.8 V DC) and reports Celsius temperature values in 0.1 °C increments.

When selecting a sensor, consider Pt100 versus thermocouple characteristics and cable length. Follow Delta’s three-wire diagram for a three-wire Pt100. Observe polarity and use extension or compensation cable suited to the thermocouple type. For a 4–20 mA temperature transmitter, scale the PLC value to the transmitter’s configured low and high temperatures. This helps distinguish a scaling error from a wiring fault.

NPN outputs and heater control

OUT1 and OUT2 share C0 for channel 1. OUT3 and OUT4 share C1 for channel 2. The outputs are NPN (sinking). Delta’s detailed table specifies a 12–30 V DC load circuit and resistive ratings of 0.3 A per output and 0.6 A per common. Control options include automatic PID, manual PID and ON/OFF. Each channel’s outputs can be assigned to heating, cooling or alarms. Use a power switching device suited to the heater. With time-proportional PID, check that the SSR’s DC control input is compatible with the NPN output. When choosing a cycle time for PID temperature control, consider the load and the switching device.

PLC software, cable and register addresses

For families such as DVP-SS2, DVP-SA2, DVP-SX2 and DVP-SV2, check right-side expansion support and the module limit for the exact CPU. Use WPLSoft or ISPSoft according to CPU support. ISPSoft uses COMMGR for the connection. Delta lists the UC-PRG020-12A USB-to-RS-232 cable or UC-MS020-01A serial cable for applicable CPUs with an 8-pin mini-DIN RS-232 port. Connect the PC to the CPU’s programming port.

In the ladder program, use FROM to read process values (PV) from CR#2 and CR#3 and TO to write channel setpoints (SV) to CR#4 and CR#5. The model identifier in CR#0 is H024F. Check the special module number against its position in the right-side stack. In Celsius temperature mode, a register value of 235 represents 23.5 °C. Use CR#10 to select the correct page for each channel before writing its input type and control parameters.

Editor’s Note

Inspect the model label and removable terminal blocks before buying a used module. TUN-S has transistor outputs, TUR-S has relay outputs and TUL-S has analog outputs.

Test both channels with a known-good probe. Check that the initial PV is close to room temperature, then warm the probe slightly and watch both channels respond.

If the PV looks right and the output stays off, check the run command, the heating or cooling assignment and the C0/C1 commons. When the output LED is on, measure the control signal at the switching device.

If the temperature reading jumps when a drive starts, inspect the probe cable route, cabinet grounding and sources of electromagnetic interference.

Before replacing a module, save the sensor types, setpoints, PID parameters and output assignments. Verify the reading and control direction before enabling the heater.

Related topics and modules

DVP02TUR-S relay outputs · DVP02TUL-S analog outputs · DVP02TKN-S NPN outputs with RS-485 · DVP04TC-S four-channel thermocouple measurement

Delta DVP expansion modules · Delta DVP PLC series · Second-hand Delta models · Delta DVP PLC PDF files

External references

Delta DVP Module Manual, Chapter 9 (2026, EN) · Delta DVP02TU-S / DVP02TK-S Temperature Control Manual (2019, EN) · Delta DVP02TUN-S Instruction Sheet (2015, TR/EN/ZH)