Delta DVP50MC11T

Delta DVP50MC11T EtherCAT Motion Controller for Up to 24 Axes

The Delta DVP50MC11T is a multi-axis controller in the DVP-MC family. It controls up to 24 physical axes and synchronizes servo motion over EtherCAT. Built-in I/O includes 16 digital inputs and 8 NPN transistor outputs. Typical applications include packaging, synchronized feeding, material transfer and coordinated positioning.

On a packaging line, a feed axis can establish product position while a cutting or sealing axis moves in sync with the same cycle. An electronic cam sets the follower position as a function of the master position. Check the exact EtherCAT servo drive model, axis scaling, encoder feedback and home reference when setting up this type of machine.

Axis capacity and hardware

Axis capacity • The DVP50MC11T base model supports up to 24 physical axes. For single-axis control, physical axes, virtual axes and encoder axes can share a total of 32 axis assignments. Delta specifies linear interpolation for up to 8 axes and circular interpolation for up to 3 axes. The -06, -04S and -16S variants support 6, 4 and 16 physical axes, respectively. Check the specification table for each variant’s interpolation capabilities.

Supply and built-in I/O • Nominal 24 V DC, operating range 20.4–28.8 V DC, maximum controller consumption 8 W. Include field devices and expansion modules when sizing the 24 V DC power supply. Use the built-in inputs for sensor and position signals and the NPN outputs for compatible DC control loads.

Encoders and expansion • The controller has two incremental encoder channels and an SSI absolute encoder interface. Check the encoder output type and supply requirements against the wiring diagram. Supported DVP-S expansion modules can connect through the left- and right-side ports as specified in the manual.

CANopen Builder and programming cable

Use Delta CANopen Builder to develop the project. Select the exact DVP50MC model shown on the nameplate. Connect the PC to the controller’s Ethernet port with a standard RJ45 Ethernet cable. Delta lists 192.168.1.1 as the default IP address for this port. Use the current address and subnet settings on an installed controller.

EtherCAT motion network • Connect the controller’s EtherCAT port to the EtherCAT input of the first drive. Connect subsequent drives using the input and output ports shown in the drive wiring diagrams. Delta lists the UC-EMC020-02B (2 m) and UC-EMC050-02B (5 m) EtherCAT cables. Compare the device order in the project with the installed EtherCAT topology. For drives such as the ASDA-A2-E, verify that the device description matches the exact drive model.

Other communication interfaces • The Ethernet port handles project transfer and Modbus TCP connections to an HMI or SCADA system. The controller also provides CANopen, RS-232 and RS-485 interfaces.

Editor’s Note

When buying a used controller, check the side nameplate as well as the front series marking. The -06, -04S and -16S suffixes affect axis count and motion capabilities.

If the PC cannot go online, check that its cable is in the Ethernet port. Then check the link LED, the controller IP address and the PC’s subnet settings.

If a drive is missing from the servo network, check its link to the preceding drive first. Then compare the device order and axis assignment with the project.

Before replacing the controller, save the CANopen Builder project, axis scaling, cam tables and EtherCAT device order. Record the machine’s current home and limit settings.

During the first motion test, keep the travel area clear and verify each axis’s direction and homing at low speed. Then test coordinated motion.

Related motion controllers

DVP10MC11T and DVP15MC11T • DVP-MC models with CANopen motion networking. DVP20PM00D • DVP-PM pulse motion controller. DVP28SV11T2 • SV2 PLC with high-speed transistor outputs. For new panels, review the I/O and communication options on Derell B Series PLCs.

Delta DVP files and used models

Delta DVP PLC PDF files · Delta DVP PLC series · Used Delta PLC models · Used PLCs and CPUs · Delta main page