Gemo DT104P-230VAC-R PID Temperature Controller
Gemo control products have been sold by our company since 2013.
Gemo DT104P is a 48x48 mm PID temperature controller for J type thermocouple input. Unlike the multi-input DT104A series, the DT104P uses a fixed Fe-Const J type thermocouple input.
Front size: 48x48 mm
Panel cut-out: 45.5x45.5 mm
Supply: 100..240VAC, 50-60Hz
Power consumption: < 8VA
There is no 24V supply version of the DT104P. An SSR control output version can be specified when ordering.
Sensor Input
Sensor: Fe-Const, J type thermocouple
Measuring range: -100 .. 600 °C
Resolution: 1 °C or 0.1 °C
Accuracy: ±0.3% of full scale
For compatible sensors, see our J type thermocouples.
Outputs
Control output: Relay, NO + NC, 250VAC, 2A resistive load
Alarm output: Relay, NO only, 250VAC, 2A resistive load
Related switching components can be found in our relay and socket section.
PID Control
Control mode: ON-OFF, P, PI, PD or PID selectable.
Heating hysteresis (H.Hys): 0 .. 50 °C. When H.Hys is set to 0, PID control is active.
Alarm hysteresis (A.Hys): 1 .. 50 °C.
Alarm setting: Absolute or relative alarm can be selected.
Proportional band (Pb.C): 1 .. 130 °C
Integral time (Ti): 0 .. 30.0 min.
Derivative time (Td): 0 .. 10.0 min.
Control period (Ct): 4 .. 200 sec.
For PID operation, a control period of approximately 4 .. 10 seconds is normally used.
If Ti is set to 0, the integral part is disabled and the controller works as P or PD. If Td is set to 0, the derivative part is disabled and control works as P or PI.
DT104P includes anti-windup and automatic overshoot reduction in PID mode.
Heating only: DT104P does not have a cooling control function.
Thermocouple Compensation
Cold-junction compensation is used for the J type thermocouple input. The controller also uses an internal °C/mV look-up table for thermocouple linearisation.
Input offset: -99 .. +99 °C. This setting can be used to correct a known difference between the actual process temperature and the displayed value.
Sensor Failure
If the thermocouple or sensor cable is open, the measurement is outside the operating range or the input cannot be measured, the controller indicates a sensor fault.
During a sensor fault, both the heating and alarm outputs remain OFF.
Other Specifications
Display: 4-digit PV + 4-digit SV, 7 segment
Heat SET: -100 °C .. Upper Limit
Protection: IP20
Operating temperature: 0 .. 50 °C
Storage temperature: -10 .. 60 °C
Operating altitude: < 2000 m
Weight: < 0.5 kg
Settings are password protected and stored in EEPROM memory when the power is switched off.
Gemo DT104P User Manual (PDF)
Installation
DT104P is intended for fixed panel mounting. Wiring and installation must be carried out by qualified technical personnel with the power disconnected.
Gemo specifies a 1A / 250VAC external fuse for the supply and a separate 2A / 250VAC fuse for each relay output.
For product or ordering information, use our Gemo contact page or email gemo@otomasyonavm.com.
```Gemo DT104P
- Mağaza: Efes Otomasyon
- Store: Efes Automation
- Brands GEMO
- Product Code: Gemo DT104p-230VAC-R
- Availability: 12
-
50.00USD
- Ex Tax: 50.00USD
Related Products
DESA-44R-A Analog Temperature Controller, 220V
▪︎ DERELL DESA-44R-A >> 220V Power Supply, Relay Output, 48x48 mm Panel Type Temperature Contr..
127.00USD Ex Tax: 127.00USD
DGS-44R-A Advanced Temperature Controller (220V)
— Next-generation temperature compensation with high precision DGS-44R-A >> 220V pow..
130.00USD Ex Tax: 130.00USD
DGS-44T-A – Advanced Serial Type with SSR Output – 220V
— Next-generation temperature compensation with high precision DGS-44T-A >> 220V pow..
135.00USD Ex Tax: 135.00USD
DGS-44R-B Advanced Temperature Controller (24VAC/DC)
— Next-generation temperature compensation with high precision DGS-44R-B >> 24VDC/AC..
201.00USD Ex Tax: 201.00USD




