• Gemo DT900

Gemo DT900 is a simple two-button digital temperature controller for ON/OFF heating applications. Depending on the ordered version, it can be used with J or K type thermocouples. OtomasyonAVM has been supplying Gemo products since 2013.

Standard supply: 100–240 VAC, 50–60 Hz.
If a 24 VAC/DC supply version is required, this must be specified when ordering.
Sensor input: Fe-Const J type thermocouple or NiCr-Ni K type thermocouple, depending on the ordered version.
Output: Relay output as standard. If an SSR output version is required, specify this when ordering.

The DT900 uses adjustable hysteresis and ON/OFF control rather than PID. This makes it suitable for straightforward heating applications where simple temperature switching is required.

Setting the temperature

The display alternates between SEt and the current SET value. Use the Up and Down arrow keys to change the required temperature.

Once the new value is shown, leave the keys untouched for approximately two seconds. The SET value is then stored automatically.

Hysteresis setting

The display alternates between Hys and the current hysteresis value. Use the arrow keys to enter the required value.

After the adjustment, leave the keys untouched for approximately five seconds. The new hysteresis value is stored automatically.

Hysteresis range: 0–50 °C.

ON/OFF control behaviour

When the measured Process Value PV ≥ SET, the OUT output switches OFF.

When PV falls to or below SET − Hys, the OUT output switches ON again.

The hysteresis setting prevents the relay from switching repeatedly around the SET temperature.

Upper SET limit

The UP.L parameter limits the highest temperature that can be entered as the SET value.

The display alternates between UP.L and the current upper-limit value. Change the limit with the Up and Down keys, then leave the keys untouched for approximately five seconds to store the new value.

Sensor fault indication

If or appears on the display, check the thermocouple and wiring. Possible causes include an open sensor circuit, measurement outside the selected range, reversed thermocouple polarity or an input fault.

Sensor protection: If the sensor circuit is open, the measurement is outside the valid range or the input cannot be measured correctly, the OUT output will not energize.

Other thermocouple and temperature-sensing options are available in our temperature sensors section.

Technical specifications

Front dimensions: 96 × 96 mm.
Display: 3-digit, 7-segment display.
Control method: ON/OFF.
Adjustable hysteresis: 0–50 °C.
SET upper limit: Adjustable with the UP.L parameter.

J type measuring range: 0–600 °C.
K type measuring range: 0–999 °C.
J type SET range: 0–600 °C.
K type SET range: 0–999 °C.

Thermocouple compensation: Ambient temperature compensation from 0 to 50 °C.
Input: Fe-Const J type T/C or NiCr-Ni K type T/C, depending on the ordered version.

OUT relay: NO + NC, 250 VAC / 2 A resistive load.
SSR output: Optional.

Supply voltage: 100–240 VAC, 50–60 Hz or optional 24 VAC/DC.
24 V version isolation voltage: Maximum 40 VAC.
Power consumption: < 6 VA.
Protection rating: IP20 according to EN 60529.

Safety: EN 61010-1; pollution degree 1, measurement category I.

Memory: SET, hysteresis and control parameters remain stored when power is removed.

Control panel installation

The DT900 can be used in industrial panels containing AC drives and speed controllers. Thermocouple wiring should be kept away from motor and inverter output cables where possible.

Because thermocouple signals are relatively low-level, separating sensor wiring from power cables helps reduce electrical interference and unstable temperature readings.

Gemo DT900 User Manual (PDF)

Gemo price list
Gemo contact information
Gemo main page
Industrial control devices

Installation: Thermocouple, supply and output wiring should be carried out by qualified technical personnel.

Before applying power, check the thermocouple type and polarity, supply voltage and relay/SSR output configuration against the product documentation.

Write a review

Note: HTML is not translated!
Bad Good

Gemo DT900

  • 19.00USD

  • Ex Tax: 19.00USD

Related Products

DES-44-R-A is a basic temperature controller

DES-44-R-A is a basic temperature controller

DERELL DES-37-R-A | Temperature Controller DERELL DERELL DES-44-R-A | Economic Series Temper..

118.00USD Ex Tax: 118.00USD

DES-77-R-A is a basic temperature controller

DES-77-R-A is a basic temperature controller

DERELL DES-37-R-A | Temperature Controller DERELL DERELL DES-77-R-A | Economic Series Temper..

119.00USD Ex Tax: 119.00USD

DES-99-R-A is a basic temperature controller

DES-99-R-A is a basic temperature controller

DERELL DES-37-R-A | Temperature Controller DERELL DERELL DES-99-R-A | Economic Series Temper..

120.00USD Ex Tax: 120.00USD

DES-37-R-A is a basic temperature controller

DES-37-R-A is a basic temperature controller

DERELL DES-37-R-A | Temperature Controller DERELL DERELL DES-37-R-A | Economic Series Temper..

121.00USD Ex Tax: 121.00USD