Gemo DT481 is a compact 48 × 48 mm digital temperature controller with simple two-button adjustment. Depending on the ordered version, it can be used with J or K type thermocouples and provides straightforward ON/OFF temperature control. OtomasyonAVM has been supplying Gemo products since 2013.
Standard supply: 100–240 VAC, 50–60 Hz.
If a 24 VAC/DC supply version is required, this must be specified when ordering.
Sensor input: Fe-Const J type thermocouple or NiCr-Ni K type thermocouple, depending on the ordered version.
Output: Relay output as standard. If an SSR output version is required, specify this when ordering.
The DT481 is intended for applications where simple temperature switching is required in a small panel space. It uses adjustable hysteresis and ON/OFF control rather than PID.
Setting the temperature
The display alternates between SEt and the current SET value. Use the Up and Down arrow keys to enter the required temperature.
After setting the new value, leave the keys untouched for approximately two seconds. The SET value is then stored automatically.
Hysteresis setting
The display alternates between Hys and the current hysteresis value. Use the Up and Down keys to enter the required setting.
After the adjustment, leave the keys untouched for approximately five seconds. The new hysteresis value is stored automatically.
Hysteresis range: 0–50 °C.
ON/OFF control behaviour
When the measured Process Value PV ≥ SET, the OUT output switches OFF.
When PV falls to or below SET − Hys, the OUT output switches ON again.
The hysteresis setting helps prevent unnecessary relay switching around the SET temperature.
Upper SET limit
The UP.L parameter can be used to limit the highest SET value that the operator is allowed to enter.
The display alternates between UP.L and the current upper-limit value. Adjust the value with the Up and Down keys, then leave the keys untouched for approximately five seconds to store the new setting.
Sensor fault indication
If or appears on the display, check the thermocouple and its wiring. Possible causes include an open sensor circuit, measurement outside the selected range, reversed thermocouple polarity or an input fault.
Sensor protection: If the sensor circuit is open, the measurement is outside the valid range or the input cannot be measured correctly, the OUT output will not energize.
Other thermocouples and related products can be found in our industrial sensors section.
Technical specifications
Front dimensions: 48 × 48 mm.
Display: 3-digit, 7-segment display.
Control method: ON/OFF.
Adjustable hysteresis: 0–50 °C.
SET upper limit: Adjustable with the UP.L parameter.
J type measuring range: 0–600 °C.
K type measuring range: 0–999 °C.
J type SET range: 0–600 °C.
K type SET range: 0–999 °C.
Thermocouple compensation: Ambient temperature compensation from 0 to 50 °C.
Input: Fe-Const J type T/C or NiCr-Ni K type T/C, depending on the ordered version.
OUT relay: NO + NC, 250 VAC / 2 A resistive load.
SSR output: Optional.
Supply voltage: 100–240 VAC, 50–60 Hz or optional 24 VAC/DC.
24 V version isolation voltage: Maximum 40 VAC.
Power consumption: < 6 VA.
Protection rating: IP20 according to EN 60529.
Safety: EN 61010-1; pollution degree 1, measurement category I.
Memory: SET, hysteresis and control parameters remain stored when power is removed.
Control panel installation
The DT481 can be used in industrial panels containing AC drives and speed controllers. Thermocouple wiring should be kept away from motor and inverter output cables where possible.
Because thermocouple signals are relatively low-level, separating sensor wiring from power cables helps reduce electrical interference and unstable temperature readings.
Gemo price list
Gemo contact information
Gemo main page
Industrial control devices
Installation: Thermocouple, supply and output wiring should be carried out by qualified technical personnel.
Before applying power, check the thermocouple type and polarity, supply voltage and relay/SSR output configuration against the product documentation.
Gemo DT481
- Mağaza: Efes Otomasyon
- Store: Efes Automation
- Brands GEMO
- Product Code: Gemo DT481-230VAC-R
- Availability: 17
-
18.00USD
- Ex Tax: 18.00USD
Related Products
DESA-44R-A Analog Temperature Controller, 220V
▪︎ DERELL DESA-44R-A >> 220V Power Supply, Relay Output, 48x48 mm Panel Type Temperature Contr..
127.00USD Ex Tax: 127.00USD
DGS-44R-A Advanced Temperature Controller (220V)
— Next-generation temperature compensation with high precision DGS-44R-A >> 220V pow..
130.00USD Ex Tax: 130.00USD
DGS-44T-A – Advanced Serial Type with SSR Output – 220V
— Next-generation temperature compensation with high precision DGS-44T-A >> 220V pow..
135.00USD Ex Tax: 135.00USD
DGS-44R-B Advanced Temperature Controller (24VAC/DC)
— Next-generation temperature compensation with high precision DGS-44R-B >> 24VDC/AC..
201.00USD Ex Tax: 201.00USD




