What Is Fieldbus?

What Is Fieldbus?

How controllers and field devices exchange useful data

Fieldbus describes industrial networking used to exchange digital data between a control system and equipment such as instruments, drives, valves and remote I/O. It is a family of communication approaches, rather than one brand or protocol. A PLC can send commands and receive measurements, status and diagnostic information through a suitable network. See our industrial communication guide for the wider context.

A conventional 4–20 mA connection carries a measurement as an analogue signal. A networked device may additionally expose status, parameters and diagnostic data, depending on its capabilities. Sharing a network can reduce separate signal wiring. It does not automatically mean that every device receives power through the communication cable; power arrangements depend on the technology.

Separate the electrical interface from the protocol

The physical layer defines how signals travel electrically or optically. The protocol defines message structure and communication rules. The data mapping explains what the transferred values mean.

RS-485 specifies an electrical interface. Modbus defines a communication protocol. Two RS-485 ports need not speak the same protocol. Similarly, an RJ45 connector is not proof that two industrial Ethernet devices can exchange application data directly.

What does a drive command actually contain?

Consider an illustrative Modbus RTU installation in which the PLC addresses a drive as device 7. It writes a speed reference to the register specified by the drive manufacturer and reads actual frequency from another register. Other devices may receive the message electrically, but only the addressed device replies to an ordinary unicast request.

If the manual specifies a frequency resolution of 0.01 Hz per count, a received value of 2500 represents 25.00 Hz. This is an example, not a universal drive mapping. Verify the register address, data type and scaling before using the result. The drive may also require its command source to be set to the communication interface before network commands can control it.

Recognising the main technology families

PROFIBUS serves factory and process automation; its DP and PA implementations have different physical connection arrangements. CANopen provides an application layer and communication profiles for CAN-based devices. FOUNDATION Fieldbus H1 and HSE are distinct networking technologies associated with process instrumentation.

PROFINET, EtherCAT and EtherNet/IP use Ethernet-based industrial communication. Their connection and data exchange methods differ from traditional serial buses. Nevertheless, fieldbus is not a synonym for RS-485: EtherCAT is also described as an Ethernet fieldbus.

Link speed does not tell you when data will arrive

Bit rate describes transmission speed. Cycle time describes how often the required data is refreshed. Jitter describes variation in timing. A temperature measurement and coordinated servo motion can have very different timing requirements. Our real-time communication explanation develops this distinction.

Device count, message length, processing delays and retries affect the overall update time. Not every network uses the same sequential polling method. The permitted network topology also depends on the technology: a line, star or ring should only be used where the selected system supports it.

Diagnose the symptom before changing settings

No data at all: check power, the correct communication port, protocol selection and device identity. For serial Modbus, baud rate, parity and stop-bit settings must agree. Other technologies require their own addressing and configuration procedures.

Data arrives but makes no sense: check the register or object address, data type, scale factor and ordering of multi-byte values. Two products can support the same protocol while exposing different data maps.

Intermittent communication: inspect connectors, shielding, cable routing, segment length and network diagnostics. Modbus over RS-485 requires termination appropriate to the two ends of the bus; adding a resistor at every device is not the solution. PROFIBUS RS-485 uses a different, active termination arrangement. For EtherCAT installations, see the network troubleshooting guide.

Define what happens when communication is lost. Holding the last command, stopping under control or generating a fault depends on device settings and the application. A watchdog can supervise communication, but an ordinary timeout does not by itself constitute a functional safety function.

Standards and device compatibility

IEC 61158 organises fieldbus specifications into a series. IEC 61784 addresses industrial communication profiles. The CPF and CP concepts identify communication profile families and individual profiles. A shared standard reference alone does not establish full compatibility: check the protocol, profile, supported features and device configuration file together.

References and sources

IEC 61158-1:2023 · Modbus Organization — Specifications · PI — PROFIBUS · PI — PROFINET · CiA — CANopen · ETG — EtherCAT · FieldComm Group — FOUNDATION Fieldbus


Refine Search