6ES7 133-1BL01-0XB0

6ES7 133-1BL01-0XB0 – Siemens ET 200L 16 DI / 16 DO

Series: SIMATIC ET 200L
Category: 24 V DC digital input/output electronics block

Purpose and system role

6ES7 133-1BL01-0XB0 is an ET 200L electronics block in the Siemens ET 200 family, combining 16 digital inputs and 16 digital outputs. It exchanges field signals with the PLC over PROFIBUS DP. The supervising controller executes the user program; this block provides I/O connections near the machine.

Inputs and sensor selection

The inputs accept 24 V DC signals. The specified high-state range is 13–30 V, with an input delay of 2–4.5 ms in both directions. Check the output circuit when selecting a sensor: a 24 V supply rating alone does not establish that an inductive sensor has a compatible output. For short pulses, assess input delay together with the PLC cycle.

Output current and aggregate load

Each output is rated at 0.5 A with a 24 V DC load supply. When choosing suitable solenoid valves, relays or DC contactors, consider pull-in current as well as continuous current. The outputs have short-circuit protection; two outputs must not be paralleled to increase current capacity.

The manual specifies aggregate current per output byte: for horizontal mounting, 4 A up to 30 °C, 3 A up to 40 °C and 2 A up to 60 °C. Other mounting positions permit 2 A up to 40 °C. Do not assume all 16 outputs can continuously carry 0.5 A under every operating condition; distribute loads according to cabinet temperature.

TB 32L terminal block and power connections

The electronics block requires a TB 32L base: 6ES7 193-1CL00-0XA0 for screw terminals or 6ES7 193-1CL10-0XA0 for spring terminals. The terminal block carries the field wiring and is a separate component from the electronics block. Check what is included when purchasing a replacement.

Check the electronics supply and the sensor/load supplies separately against the wiring diagram. An illuminated ON LED does not establish that every load circuit has power. Size the power supply for the sensors and simultaneously active loads as well as the electronics. When comparing DIN-rail power supplies, use the complete load requirement and the actual cabinet temperature.

PROFIBUS configuration and diagnostics

The maximum communication rate is 1.5 Mbit/s. Cyclic data occupies 2 input bytes and 2 output bytes. Do not apply the 12 Mbit/s rating of other ET 200 families. This model does not use PROFINET; account for the differences between ET 200 communication interfaces when planning a network change.

During commissioning, compare the PROFIBUS address, GSD/hardware entry and I/O addresses with the existing project. If communication fails, first check power, connectors, bus termination and duplicate addresses. BF indicates a bus fault, while ON helps monitor the electronics supply. If an output LED is on but its load does not operate, continue measurements at the load supply, output terminal and return conductor.

Replacement of the earlier 1BL00 version

6ES7 133-1BL01-0XB0 and the earlier 6ES7 133-1BL00-0XB0 share the 16 DI/16 DO arrangement, but Siemens distinguishes their sensor-supply protection requirements. Before copying an existing wiring and fuse arrangement, check the complete order number, terminal diagram and installed protective devices together.

Editor’s Note

Two useful checks are the condition of the TB 32L base and output behaviour under a representative load. Successful communication or illuminated channel LEDs alone do not establish that every output is healthy. Monitor load current, output voltage and supply voltage drop together. For replacement selection, match the 16-input/16-output layout, complete order number, terminal block and PROFIBUS configuration.

Manuals and PDF documents

Use the Siemens ET 200 manuals and PDF documents page to find the relevant documentation. Technical references: Siemens ET 200L Distributed I/O Device, 10/2005, EWA-4NEB780600902-05, sections 3.2, 7.2, 8.5 and appendix B. Read these together with the Siemens data sheet for this exact model.

Related topics

About Siemens ET 200 · PLCs and modules · PLC and HMI systems · ET 200 terminal blocks

Navigation

Home · Siemens · Siemens S7 PLC · SIMATIC S7 · Siemens ET 200 · ET 200 manuals