6ES7 133-0HH01-0XB0

6ES7 133-0HH01-0XB0 – Siemens ET 200B 8DI/8RO

Series: Siemens SIMATIC DP / ET 200B
Category: Electronic block with 8 digital inputs and 8 relay outputs

Description and system role

6ES7 133-0HH01-0XB0 is an ET 200B electronic block in the Siemens ET 200 family. It combines 120/230 V AC digital inputs with relay outputs and exchanges field data with the controller through integrated PROFIBUS DP communication. The control program runs in the connected PLC, while this block provides I/O points near the machine.

When using SIMATIC S7 or another suitable DP master, consider the electronic block and terminal base as a matched assembly. Within the ET 200 system, ET 200B uses compact blocks with fixed channel counts. Components from another ET 200 series should not be assumed to fit the same base.

Key specifications

Inputs: 8 digital inputs. Input voltage class: 120/230 V AC. Outputs: 8 relay outputs. Electronic block width: 235 mm. Matching terminal base: TB6/AC, order number 6ES7 193-0CC10-0XA0, with three-tier screw terminals.

The block combines digital input and digital output functions. The 120/230 V AC input rating does not establish the switching capacity of every relay contact for every load. Contact selection must account for load type, operating voltage, switching frequency and ambient conditions.

Terminal base and wiring

Check the TB6/AC order number and the electronic block label when selecting a terminal block; matching width alone is insufficient. Establish whether a replacement includes the base or only the electronic block. Inspect the connection components, terminal condition and existing wiring drawings before replacement.

Review the AC input circuits, electronics supply and relay load circuits separately. Signals from auxiliary contacts require a circuit suitable for the input voltage. Do not assume a 24 V DC sensor output can directly operate these AC inputs. Qualified personnel should isolate the relevant circuits and verify the absence of voltage before wiring or removal.

PROFIBUS and project checks

The station operates on PROFIBUS DP. Back up the existing project and compare the station address, configured device and I/O addresses with the installed hardware. The engineering software must have the appropriate hardware definition or GSD file.

When investigating communication faults, check the supply, duplicate addresses, bus connector, cable shielding and termination first. Compare alarms on the HMI or SCADA system with PLC diagnostics and the actual field condition.

Relay outputs and load selection

For interposing relays and contactor coils, consider pickup current, holding current and suitable suppression components. A motor or other substantial load should not be connected directly based only on its running current. Select switchgear and circuit protection for the actual load characteristics.

On a used block, an active output command alone does not prove that the relay contact performs correctly under load. Test inputs and outputs individually using a suitable setup, checking for sticking contacts, inconsistent switching and excessive contact voltage drop.

Editor's Note

Pay particular attention to the 0HH01 suffix and the TB6/AC base. The 8DI/8RO section in the older ET 200B manual identifies 6ES7 133-0HH00-0XB0. Its relay current and load limits have therefore not been presented here as confirmed specifications for 0HH01. Assess the complete label, terminal base and intended loads together when choosing a replacement.

PDF manuals and technical references

The ET 200B Distributed I/O Station manual explains the system architecture and wiring approach. Page 5/212 of the Siemens IK PI 2004 catalog lists this order number and the TB6/AC base. Visit Siemens ET 200 PDF and user manuals for the documentation page. Before using detailed electrical limits, verify that the document covers the complete device order number.

Related topics

About ET 200 · ET 200 digital inputs · ET 200 digital outputs · ET 200 additional modules · ET 200 terminal blocks

Quick links: Siemens ET 200 · Siemens S7 · Siemens S7 PLC · PLC and HMI · OtomasyonAVM home