6ES7 133-0BL00-0XB0
6ES7 133-0BL00-0XB0 – Siemens ET 200B 16DI/16DO
Series: Siemens SIMATIC DP / ET 200B
Category: Electronic block with 16 digital inputs and 16 digital outputs
Description and system role
6ES7 133-0BL00-0XB0 is an ET 200B electronic block with 16 inputs and 16 outputs, all rated for 24 V DC, in the Siemens ET 200 family. It exchanges machine signals with the central PLC over PROFIBUS DP. The controller runs the application program, while this block handles the field I/O.
In a system using SIMATIC S7 or another suitable DP master, the electronic block fits onto a compatible terminal base. The ET 200B architecture uses compact blocks with fixed channel counts. Before selecting a replacement, check the complete order number, terminal base, output loads and configured device.
Input and output specifications
Digital inputs: 16 channels, 24 V DC, with a 3 ms input delay. The specified signal ranges are −30 to +5 V for “0” and +13 to +30 V for “1”. Check the output circuit and leakage current of sensors connected to the digital inputs; a 24 V supply rating alone does not establish compatibility.
Digital outputs: 16 channels, 24 V DC, maximum 0.5 A per channel. There are two groups of eight outputs, each limited to 2 A total load current. Electronic short-circuit protection is provided. When selecting digital outputs, consider both the individual channel limit and the combined current of simultaneously active loads.
For interposing relays or contactor coils, check pickup current, holding current and suitable suppression. Use an appropriate intermediate driver where the load exceeds the block's capability.
Power supply and dimensions
Rated supply: 24 V DC; permissible range 18.5–30.2 V DC. L5+/M5 supplies the electronics and sensors; L1+/M1 and L2+/M2 serve the output groups. These supply pairs are not internally interconnected. Size the power supply and distribution wiring for the electronics, sensors and output loads together.
Electronic block with terminal base: 235 × 130 × 60 mm (width × height × depth). Approximate combined weight: 800 g. Allow additional cabinet space for cable routing and servicing.
Compatible terminal bases
The listed bases include TB2/DC — 6ES7 193-0CB10-0XA0, TB2-4/DC — 6ES7 193-0CB20-0XA0, TB4/DC — 6ES7 193-0CB30-0XA0 and TB4M/DC — 6ES7 193-0CE30-0XA0. Siemens' supplementary product information also identifies the 16DI/16DO block as suitable for TB4-4/DC — 6ES7 193-0CB40-0XA0.
Differences in terminal layout and potential distribution between terminal bases matter when wiring the assembly. In particular, do not confuse the additional M terminals on TB4M/DC with PE terminals. Match the connection components and terminal markings to the diagram for the selected base. Confirm whether the supplied replacement includes the terminal base.
Communication and fault checks
Network: PROFIBUS DP, up to 12 Mbit/s. The usable rate depends on the master and network conditions. Before replacement, back up the project and compare the station address, device configuration and I/O addresses with the existing installation.
RUN indicates operating/supply status, BF a bus fault and DIA group diagnostics for short circuits or missing load voltage. L1+/L2+ LEDs help check the output supplies. Compare HMI or SCADA alarms with PLC diagnostics. If a load fails to operate, inspect its group's supply, wiring and load first.
Editor's Note
The 2 A limit per group is easy to overlook. Eight loads drawing 0.3 A each total 2.4 A. Every channel is below its 0.5 A limit, but the group is overloaded. Account for loads that operate together when distributing them between groups. Output LEDs alone do not establish that a used block performs correctly under load.
PDF manuals and technical references
Section 7.3.9 of the ET 200B Distributed I/O Station manual covers this model. Wiring information appears on pages 7-65/7-66 and specifications on page 7-67. Consult the supplementary product information for TB4-4/DC as well. Visit Siemens ET 200 PDF and user manuals for the documentation page.
Related topics
ET 200 digital inputs · ET 200 digital outputs · ET 200 terminal blocks · ET 200 additional modules · ET 200 communication interfaces
Quick links: Siemens ET 200 · Siemens S7 · Siemens S7 PLC · PLC and HMI · OtomasyonAVM home