6ES7 132-4HB10-0AB0

Siemens 6ES7132-4HB10-0AB0 ET 200S 2 Relay Output Module

6ES7132-4HB10-0AB0 is a 15 mm-wide electronic module with two changeover relay outputs for SIMATIC ET 200S. Each channel provides a common terminal, a normally open NO contact and a normally closed NC contact. Within the range of Siemens industrial automation products, it controls suitable solenoid valves, contactor coils and indicator lights within the specified load limits.

This module belongs to the ET 200S family within the Siemens ET 200 distributed I/O range. NO and NC are the two positions of the same relay; they do not provide four independent outputs. In industrial automation applications, determine when each load should receive power by reviewing the circuit diagram and machine operating sequence together.

Supply voltage and contact capacity

The manufacturer describes the module as 24–48 V DC / 5 A and 24–230 V AC / 5 A. Its 24 V DC electronic supply from the power module must be distinguished from the load circuit switched by the contacts. In PLC-based control applications, a relay contact switches an external load supply; it does not generate the load voltage.

The 5 A figure is not a universal switching rating for every voltage and load type. Siemens specifies a maximum channel current of 5 A up to 50 °C and 4 A at 60 °C. Also check the table for the load type, voltage and required contact endurance. Coil inrush and the voltage generated when an inductive load is disconnected are particularly relevant.

Five checks before selection or replacement

1. Load and switching duty: When selecting a valve or contactor for SIMATIC S7 control systems, consider more than its steady-state current. Maximum switching frequency is 2 Hz for resistive loads and 0.5 Hz for inductive loads. Include mechanical contact endurance when assessing frequently switched applications.

2. NO/NC selection: With the relay de-energized, the common terminal connects to NC. An output command of “0” therefore does not necessarily switch off a load supplied through NC. Review the stopping sequence against both the program and the wiring diagram.

3. Terminal module: Compatible examples include TM-E15S23-01 / 6ES7193-4CB00-0AA0 and TM-E15C23-01 / 6ES7193-4CB10-0AA0. When reviewing ET 200 system architecture and terminal selection, check the complete base code, connection method and existing wiring.

4. Output protection: There is no internal short-circuit protection; Siemens requires external 6 A fusing for the relay outputs. Select the fuse type and circuit arrangement according to the relevant manual. When comparing Siemens PLC and I/O products, also note that these outputs must not be connected in parallel to increase current capacity.

5. CPU STOP response: Check the project's substitute-value and hold-last-value settings. Verify the combined result of the 0/1 substitute value and the chosen NO/NC connection. A command displayed on HMI operator panels does not, by itself, prove that the load is energized.

Maintenance and wiring notes

If one channel is connected to a SELV/PELV circuit, the other channel must also be used with SELV/PELV. Channel isolation does not permit arbitrary mixing of voltage systems on the module. A relay click or channel LED also does not establish that the contact conducts correctly under load.

For contact load tables, terminal assignments and parameters, consult the ET 200S documents through the Siemens ET 200 PDF manuals page. Use the 2RO NO/NC section and verify the exact 4HB10 order code. For component matching, provide the installed module label, terminal code and load voltage/current details through Siemens product technical enquiries.

Editor's note: Two outputs and a 5 A marking are only the starting point. The NO/NC connection, coil inrush and daily switching count all affect suitability. For a used module, hearing the relay operate is insufficient; assess the contacts' behavior under load as well.

Related topics and Siemens navigation

Product families
Siemens main menu  |  Siemens PLC products  |  SIMATIC S7

ET 200 resources
ET 200 products  |  ET 200 system overview  |  ET 200 PDF manuals

Control and assistance
HMI operator panels  |  SCADA systems  |  Siemens product enquiries