6ES7 132-1BH00-0XB0
Siemens 6ES7132-1BH00-0XB0 ET 200L 16 DO 24 V DC / 0.5 A Electronic Block
6ES7132-1BH00-0XB0 is a 16-channel, 24 V DC / 0.5 A digital output electronic block for SIMATIC ET 200L. Its outputs are arranged in two groups of eight channels. Part of the Siemens industrial automation range, it controls suitable solenoid valves, DC contactors and indicator lights.
Within the Siemens ET 200 distributed I/O family, this model uses the ET 200L architecture and communicates over PROFIBUS DP. When selecting replacements for industrial automation applications, use the complete order number; “ET 200, 16 outputs” alone does not establish terminal or communication compatibility.
Calculate the combined load for each group of eight
The 0.5 A per-channel rating does not mean that all eight outputs can operate at full load at every temperature. With horizontal installation, the maximum combined current per group is 4 A up to 30 °C, 3 A up to 40 °C and 2 A up to 60 °C. Other mounting positions allow 2 A per group up to 40 °C. In PLC-based control applications, assess the loads, simultaneously active channels and cabinet temperature together.
Five checks before selection or replacement
1. Terminal block: This electronic block uses TB 16L. The screw-terminal version is 6ES7193-1CH00-0XA0, and the spring-terminal version is 6ES7193-1CH10-0XA0. When reviewing ET 200 system architecture and terminal selection, check the electronic block and base labels separately, and compare the load-group supply connections with the existing cabinet drawings.
2. PROFIBUS and project configuration: The maximum supported transmission rate is 1.5 Mbit/s. In SIMATIC S7 control systems, verify the station address, bus speed and hardware configuration. Back up the existing project before replacement; a matching connector alone does not guarantee communication compatibility.
3. Load type and switching: Maximum switching frequencies are 100 Hz for resistive loads, 0.5 Hz for inductive loads and 8 Hz for lamp loads; maximum lamp load is 5 W. Outputs must not be paralleled to increase current capacity. Check coil starting current when selecting valves or contactors.
4. Voltage drop and off-state behavior: At signal “1”, output voltage is at least load supply voltage − 3 V. Residual current at signal “0” is up to 1 mA. Consider these values when matching low-current electronic loads to the Siemens PLC and I/O range. Assess cable length, low supply voltage and the load's operating threshold together.
5. Indication and troubleshooting: BF helps monitor communication status, ON indicates the electronics supply, and green channel LEDs show output status. A command on HMI operator panels or an illuminated channel LED does not confirm mechanical valve operation. If communication is healthy but one group does not operate, check that group's load supply as well.
PDF manuals and technical assessment
Access documentation resources through the Siemens ET 200 PDF manuals page. For this product, refer to Section 8.2 of the ET 200L Distributed I/O Device, 10/2005 manual, and Section 7.1 for terminal selection. Provide the module label, TB 16L code and connected load details through Siemens product technical enquiries.
Editor's note: Eight loads drawing 0.35 A each produce a group total of 2.8 A. With horizontal installation, this is below the 3 A limit at 40 °C but above the 2 A limit at 60 °C. Keeping individual channels below 0.5 A is insufficient; check the group total under hot cabinet conditions too.
Related topics and Siemens navigation
Product families
Siemens main menu |
Siemens PLC products |
SIMATIC S7
ET 200 resources
ET 200 products |
ET 200 system overview |
ET 200 PDF manuals
Control and assistance
HMI operator panels |
SCADA systems |
Siemens product enquiries