6ES7 132-0BH01-0XB0
Siemens Main Menu | SIMATIC S7 | Siemens ET 200 | PDF Manuals
6ES7 132-0BH01-0XB0 — Siemens SIMATIC DP ET 200B 16-Digital-Output Module
Series: SIMATIC DP ET 200B
Product type: 16-channel 24 V DC digital-output electronics block
Order number: 6ES7132-0BH01-0XB0
6ES7 132-0BH01-0XB0 is a 16-channel digital-output block for the ET 200B series in the Siemens ET 200 distributed I/O family. It connects 24 V DC solenoid valves, DC contactors and indicator lamps to a SIMATIC S7 automation system through PROFIBUS-DP. Its defining output mix is 12 × 0.5 A plus 4 × 2 A.
ET 200B architecture and channel arrangement
This product uses a different hardware architecture from the slim electronics modules in ET 200S. The ET 200B electronics block combines output electronics, the PROFIBUS-DP interface, station-address selection and status LEDs. When comparing ET 200 digital output modules, channel count and current rating are therefore not sufficient; the ET 200B family and a compatible terminal block must also match.
The sixteen outputs are divided into two eight-channel groups, Q0 and Q1. In each group, channels .0 and .1 can supply up to 2 A, while the six channels from .2 through .7 can supply up to 0.5 A. Siemens specifies a 4 A maximum total per group, so the individual channel ratings must not simply be added as if every channel could deliver its maximum simultaneously.
Key technical specifications
Supply and load voltage: 24 V DC; permissible range 18.5–30.2 V DC.
Digital outputs: 16 channels; 2 × 2 A and 6 × 0.5 A per group.
Output groups: 2 × 8 channels; 4 A maximum total per group.
Short-circuit protection: electronic.
Lamp load: up to 5 W on a 0.5 A channel; up to 10 W on a 2 A channel.
Switching frequency: 100 Hz resistive, 0.5 Hz inductive and 8 Hz lamp load.
Communication: PROFIBUS-DP up to 12 Mbit/s; SYNC capable.
Degree of protection: IP20.
Dimensions: 160 × 130 × 60 mm with electronics and terminal blocks.
Weight: approximately 600 g with electronics and terminal blocks.
Power loss: 5 W maximum.
Unshielded cable length: 100 m maximum.
The Siemens data sheet lists TB1/DC, TB1-4/DC, TB3/DC and TB3-4/DC as compatible terminal-block options. The terminal block is a separate hardware component. When reviewing ET 200 terminal blocks, verify terminal design, number of tiers, wiring method and whether it is included with a used unit.
The front panel provides a green RUN LED, a red BF LED and a green status LED for each output. The system manual also describes a red DIA group-diagnostics indicator and green L1+/L2+ load-voltage indicators. These displays speed up first checks of the ET 200 PROFIBUS communication architecture and field supplies.
Six selection and commissioning checks
1. Confirm the hardware family and terminal block together. 6ES7132-0BH01-0XB0 is an ET 200B electronics block; it does not fit an ET 200S or ET 200L base. Compare the ET 200 system architecture against the station label, terminal-block code and mechanical dimensions.
2. Separate channel current from group current. Each group contains two 2 A outputs and six 0.5 A outputs, but the group total is limited to 4 A. If both 2 A channels in one group operate at full load, no continuous-current budget remains for its other six channels. Account for simultaneous operation and inrush current when distributing loads between the two groups.
3. Do not confuse the functions of L1+, L2+ and L3+. Q0 is supplied from L1+, Q1 from L2+, and internal logic from L3+. These three positive terminals are not internally interconnected. When designing the ET 200 power supply arrangement and ET 200 power distribution, assess protection, common M connections, conductor size and voltage drop separately for each output group.
4. Verify the PROFIBUS project and address. The block supports PROFIBUS-DP up to 12 Mbit/s and the SYNC function. The installed DP master, project version and GSD/type file may nevertheless impose a lower rate or a specific hardware definition. Record the current station address, bus termination and ET 200 connection arrangement before removal.
5. Match load type to output limits. The switching limit for inductive loads such as solenoids and DC contactors is 0.5 Hz. If external suppression, an interposing relay or a contactor is required, consider coil voltage, release time and fault behaviour together. Full-load lamp wattage and cable voltage drop must also be considered when choosing ET 200 supplementary modules and accessories.
6. Complete LED information with real load feedback. RUN, BF and channel LEDs indicate supply, communication and output command states; none alone proves that a valve moved or a contactor picked up. Monitor a limit switch or auxiliary contact through ET 200 digital input modules for critical actuators.
Installation and maintenance details
Because the module is rated IP20, install it inside a suitable electrical enclosure. The operating range is 0–60 °C for horizontal installation; the upper limit is 40 °C in other mounting positions. Before removing or fitting a terminal block, safely isolate both load and electronics supplies and remember that L1+, L2+ and L3+ are separate.
For a used unit, ask whether a compatible terminal block is included with the electronics block. Inspect for heat marks at terminals, housing cracks, damage to the PROFIBUS connector, play in the address selector and recurring DIA indications on an output group. Sharing the product label and clear hardware photographs through the Otomasyon AVM Siemens contact page supports a more reliable compatibility assessment.
Editor’s note
The most common calculation error with this model is to add 12 × 0.5 A and 4 × 2 A and assume that all outputs can deliver those loads at the same time. The actual limit is 4 A total for each eight-channel group. If both high-current channels in one group operate at their full 2 A rating, that group’s current budget is already exhausted. Before purchase or commissioning, map the channel list to Q0/Q1 and check continuous load, inrush current and simultaneous-operation scenarios separately.
PDF manuals and documentation
Consult section 7.3.3 of ET 200B Distributed I/O Station — EWA 4NEB 812 6089-02c and the Siemens product data sheet on the Siemens ET 200 PDF manuals page. The manual documents channel assignments, L1+/L2+/L3+ connections, terminal-block wiring, LED diagnostics and the group-current limit. This page is selection guidance; use the device label, project documentation and manufacturer manual as the final authority for wiring and commissioning.
Related topics and Siemens navigation
Digital output modules | Terminal blocks | Power supply modules
Power distribution modules | PROFIBUS interfaces | ET 200 system architecture
Siemens Main Menu | SIMATIC S7 | Siemens ET 200 | PDF Manuals