6ES7 141-1BF00-0XB0

Siemens main menu › SIMATIC S7 › SIMATIC ET 200

Siemens 6ES7 141-1BF00-0XB0 — ET 200X BM 141, 8 DI 24 V DC

6ES7 141-1BF00-0XB0 is an ET 200X BM 141 basic module in the Siemens ET 200 distributed I/O family. It collects sensor and contact signals through eight 24 V DC digital inputs and connects to the higher-level control system through an integrated PROFIBUS DP interface. When reviewing the ET 200 digital input range, consider its role as the station's basic module as well as its input count.

Order number: 6ES7141-1BF00-0XB0
Series / module: SIMATIC ET 200X / BM 141
Function: Basic module with digital inputs
Inputs / rated voltage: 8 DI / 24 V DC
Sensor connections: 5-pole M12, dual channel assignment
Communication: Integrated PROFIBUS DP, up to 12 Mbit/s
Protection rating in the product description: IP65

The BM 141's role in the station

Within the ET 200 system architecture, the BM basic module combines the station's fieldbus connection with its own inputs. An EM expansion module is added to a compatible basic module. Replacing this component therefore requires checking the network connection and attached expansion modules alongside the local inputs. The distinction between PROFIBUS and PROFINET in the ET 200 communication options matters here: this product is specified with PROFIBUS DP.

A documented ASM 473 compatibility limit

The Siemens SIMATIC RF300 System Manual, 04/2006, Table 7-13, lists 6ES7141-1BF00-0XB0 as not suitable for operation with either ASM 473 — 6GT2002-0HA00 or ASM 473 PARAM — 6GT2002-0HA10. When selecting from the ET 200 special-function and expansion module range, the ET 200X family name alone is therefore insufficient. The 6ES7141-1BF00-0AB0 listed in the same table is a different product; the A / X difference in the suffix matters.

Five checks before selection or replacement

1. Complete reference and revision: Record the full 6ES7141-1BF00-0XB0 reference and hardware revision from the label. Do not directly apply technical tables for 1BF01, 1BF11 or 1BF12 to this earlier version. When comparing components through the Siemens main menu, check connections, project identification and expansion requirements as well as channel count.

2. PROFIBUS address and project: Document the existing station address, cable route and segment termination before replacement. The hardware record in the Siemens S7 hardware project must match the installed module sequence. Do not assume that a different basic module fitted in the same physical position will work without a project change.

3. M12 input connections: With dual channel assignment, carrying two separate input signals through a socket depends on the cable using the correct pins. When assessing ET 200 connection components and sensor splitters, check the existing socket-to-channel mapping. Cable colours or a pin table for another ET 200 model are not sufficient references on their own.

4. Supply and common return: Checks of ET 200 power supply components should extend beyond the power supply output to the basic module and sensor connections. When assessing ET 200 power distribution, consider fusing, common return connections and voltage drop under load together. An input that remains off may indicate a sensor, wiring or supply problem.

5. Expansion and mechanical condition: Record the complete references and sequence of attached modules, and check the operating requirements of each one with this BM revision. Modules in the ET 200 digital output range require separate checks of load supply and output capacity. Inspect side connections, socket threads, seals and covers on unused connections; do not assume sealing is maintained with missing or damaged parts.

Editor's note

For this model, the maintenance record should centre on the basic module label, PROFIBUS address and station module sequence. “ET 200X, eight inputs” is not a complete replacement specification. Checking the full reference, particularly 0XB0 / 0AB0, helps prevent incorrect compatibility assumptions.

Manuals and PDF documentation

Access ET 200X documentation through our Siemens ET 200 PDF and user manuals page. For wiring and electrical limits, check that the document covers the 1BF00-0XB0 version; sections describing newer BM 141 modules do not automatically apply. For ASM compatibility, consult SIMATIC RF300, J31069 D0166-U001-A2-7618, 04/2006, page 7-38, Table 7-13.

Related topics and Siemens navigation

Product family: Siemens main menu  |  SIMATIC S7  |  ET 200 family

Station and field devices: Digital input modules  |  Additional modules  |  PROFIBUS and PROFINET

Technical resources: About ET 200  |  Power supply modules  |  ET 200 PDF manuals