6ES5 951-7NB21
Siemens 6ES5 951-7NB21 SIMATIC S5-115U/H Power Supply
The Siemens 6ES5 951-7NB21 is a PS 951 rack power supply for S5-115U and S5-115H systems in the SIMATIC S5 family. It powers the CPU, backplane and I/O control circuits. The nominal input is 24 V DC, with a range of 19.2–30 V DC, and the main output is 5 V DC (±1.5%) / 3 A. There is no galvanic isolation between the 24 V input and 5 V output.
If a CPU 941 or CPU 942 loses power along with several other modules, start with the 24 V input and the 5 V rack rail. If the fault is confined to an expansion rack, check its local supply and the S5 interface module connection separately.
Input, main rail and auxiliary outputs
The DC input is on L+ and M. Siemens specifies a rated input current of 1.51 A at 24 V. The allowable load on the 5 V output is 0.3–3 A, and the 3 A rating also applies in a fan-cooled rack. During replacement, check the S5 wiring and connectors, rack reference potential and protective earth arrangement against the cabinet drawings.
The programmer and operator panel rail is rated at 5.2 V DC / 1 A maximum. The auxiliary rail is rated at 24 V DC / 0.2 A maximum and serves circuits such as the 20 mA current-loop interface described by Siemens. Trace the field supply separately when checking sensors for digital inputs or loads on digital outputs.
Matching the rack and the existing PS 951
Check the S5 rack label and the current draw of the installed modules before choosing a spare. For rack configurations such as the 6ES5 700-0LA11 and 6ES5 700-3LA12, use the corresponding system manual to verify the power supply slot and module layout. The Siemens S5-115H manual lists the 7NB21 as a non-isolated 3 A option with a 24 V DC input.
With a CPU 944 or CPU 945 in an S5-115U configuration, count the CPU and all installed modules in the 5 V load. The 6ES5 951-7LB21 is also rated at 3 A and has an AC input. Siemens lists separate module restrictions for the 6ES5 951-7NB13 where the DSI signal is required. The 24 V DC 6ES5 951-7ND51 is rated at 7 A, or 15 A with the specified fan.
Battery compartment and front-panel indicators
Siemens lists the 7NB21 spare part with the backup battery ordered separately. The module has a compartment for a size C, 3.6 V / 5 Ah lithium backup battery and an EXT BATT input for external backup. BATT LOW reports battery status. The 5 V, 5.2 V and 24 V indicators show the operating voltages. Check the S5 memory card type and program backup before isolating power.
Editor’s note
Get clear photos of the 7NB21 suffix and the rack label. The PS 951 and 3 A markings alone leave the input type and version ambiguous.
If the PLC drops out during startup, have the 24 V measured under load at the module’s L+ and M terminals. That reading includes any voltage drop along the upstream supply, terminals and cable run.
If the rack became unstable after a module was added, recalculate the 5 V load first. The 7NB21 remains rated at 3 A with a fan fitted.
If BATT LOW is lit, check whether the battery is fitted correctly and in good condition. After servicing it, follow Siemens’s RESET procedure on the power supply.
For a used power supply, ask for a loaded 5 V reading in a compatible rack and test results for the auxiliary rails. Confirm separately whether the battery is included.
OtomasyonAVM resources and PDFs
+ SIMATIC S5 power supplies · Siemens S5 PLC overview
+ SIMATIC S5-115H System Manual (English PDF) · Table 3-7, 7NB21 power supply selection.
Related topics
+ 6ES5 951-7NB13 · 24 V DC input, 3 A version.
+ 6ES5 951-7LB21 · AC input, 3 A version.
+ 6ES5 951-7ND51 · 24 V DC input, 7/15 A version.
To offer a 7NB21 for sale, email a nameplate photo, quantity and test status to otomasyonavm@gmail.com.
Navigation
+ S5 power supplies · S5-115U and related CPUs · SIMATIC S5 · Used Siemens equipment
External references
+ Siemens S5-115U System Manual (English PDF) · p. 15-11, 7NB21 ratings and front-panel drawing.
+ Siemens 6ES5 951-7NB21 order data sheet (German PDF) · S5-115U/H and battery supply details.