6ES5 950-1AB61
Siemens 6ES5 950-1AB61 EG 182-3K power supply, 24 V DC input, 5.1 V DC / 8 A output
The Siemens 6ES5 950-1AB61 is a PS 950 power supply for the EG 182-3K compact expansion rack in SIMATIC S5 systems. It takes 24 V DC and delivers 5.1 V DC at 8 A to the rack electronics. Siemens’ ST 53 catalogue lists the 6ES5 182-3KH61 as an 18-slot EG 182-3K configuration with these supply ratings.
The unit supplies the 5 V electronics in the S5 expansion rack. The 6ES5 950-3AA51 also takes 24 V DC and has an 8 A output rating, but Siemens lists it for the ZG 130A and EG 182-3A family. The 6ES5 182-3AA21 is an example of an A-type expansion rack. The 6ES5 950-8MD11 also carries the PS 950 designation and is an AC-input, 24 V DC output supply for the S5-100U.
24 V DC input and 5.1 V rack output
The operating input range is 20–30 V DC, including ripple. Permissible ripple is 3.6 V peak to peak, and input current at rated load is 2.5 A. Siemens specifies a maximum inrush of 100 A for 0.3 ms. The main output tolerance is ±1%. The input and output circuits are galvanically connected.
If several digital input, digital output or combined I/O modules fail together, check the common 5 V rack supply. For an output module such as the 6ES5 444-3AA11, record the rack electronics supply and the 24 V field load supply as separate measurement points.
EG 182-3K rack connections
Identify the S5 interface linking the central controller to the expansion rack. Siemens’ ST 53 catalogue lists the 6ES5 312-3AB11 as a 312-3 option with a 50 cm cable for an expansion rack mounted above the controller. The table for rugged racks such as the EG 180/181 lists separate part numbers, including the 312-5AA13 and 312-5AA31.
Record the green power supply LED separately from the indicators on the IM 300 or IM 301 interface. The Siemens manual associates the 301-3 Störung fault indication with loss of either the internal 5 V supply or the external 24 V load supply.
Front-panel U and I test points
The green LED lights when both input and output voltage are present. The U test point shows output voltage. The I test point represents output current at 10 mV per amp. For example, 50 mV at I corresponds to 5 A of load current.
The EG 182-3KH61 configuration has a separately documented 220 V AC supply for its fan assembly. When investigating a fan fault, trace that circuit and the PS 950’s 24 V DC input separately. Compare the rack’s cables and connectors with the manual’s wiring diagram.
Editor’s note
Check the rack and power supply labels together. When requesting a spare, include the 1AB61 label, the EG 182 rack number and a photo of the connector side. The A or K designation on the rack affects which spare to order.
Capture the 24 V input during startup. If the fault occurs at switch-on, check whether the input dips below 20 V. Record the unloaded reading and the startup reading separately.
Log the U and I readings separately. The millivolt reading at I represents load current. Record U in volts, I in millivolts and the equivalent output current in amps.
Confirm the program backup if the central controller will also be shut down. Check that the STEP 5 backup is current. If the S5 memory configuration uses battery-backed RAM, record the condition of the central controller’s backup supply.
Ask for test results under load. When comparing used PLC power supplies, look for a report that identifies the unit and records the applied load, the 24 V input and the measured 5.1 V output.
OtomasyonAVM resources and PDFs
About Siemens SIMATIC S5 PLCs · 6ES5 182-3KH61 expansion unit
OtomasyonAVM SIMATIC S5 PDF archive · Manuals published for the S5 family.
Related topics
6ES5 950-3AA51 power supply · EG 182-3A expansion unit · 6ES5 312-3AB11 interface
Browse this family
Siemens S5 PLCs → SIMATIC S5 → S5 power supplies
External references
Siemens SIMATIC S5 manual — 950-1AB61 technical ratings (German)
Siemens SIMATIC S5 manual — front panel and U/I test points (German)
Siemens ST 53 catalogue — 24 V power supplies and rack assignments (German)